Siemens SICAM Q100 7KG95 Series Manual Download Page 212

Page: 212 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

212

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

9.3.6.8 Transient Detection

Default Settings and Setting Ranges

Parameterizing the Transient Detection

If you want to change the

Transient reference level

, proceed as follows:

✧

In the navigation window of the

Recording and Reporting

menu, click the element

Transient reference

level.

Figure 9-55

Configure tab, transient reference level input/output window

✧

Change the parameter according to Table 9-22.

✧

After the parameterization click

Send

The parameters are transmitted to the device but not enabled yet (passive set of parameters).

✧

If you do not want to make any additional settings, continue with the

Activation

of the device configuration

according to section

Activating the Set of Parameters

. If you want to change other settings, enter the

changes and then enable the device configuration as described in section

Activating the Set of

Parameters

Table 9-22

Transient Detection

Parameter

Default Setting

Setting Range

Transient refe-
rence level

110 %

110 % to 240 % of

the

nominal/declared supply

voltage

MAN_SICAM_Q100_US.book Page 212 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 212 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: