manualshive.com logo in svg

Siemens SICAM Q100 7KG95 Series, Manual, Page: 371 / 448

Share
Download
Siemens SICAM Q100 7KG95 Series Manual Download Page 371

13 Failures and LED Indications

13.2 Indications Signaled by LEDs

371

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

Table 13-1

Indications Signaled by LEDs on the Top Side of the Housing

LED

Meaning

No Operation

Device is switched off.

Device is switched on, but firmware is not loaded.

or

Device is in startup phase.

Normal Operation

Configured IP address is used.
or 
IP address is received via DHCP.

H1

 and 

H2

 LEDs are configured.

Normal operation with default IP address
The default IP address was requested by pressing the F4 softkey during 
normal operation.

Double IP address has been detected in the network.
The device is in operation but cannot be reached via Ethernet.
Solve this network configuration issue and restart the device.
Each device must have a unique IP address.

An IP address request via DHCP is in progress.

ERROR

 = off, H1 and H2 LEDs according to configuration

RUN

 LED stops flashing when IP address is received.

The device runs into the Fallback mode after an unresolvable error in normal 
operation occurs or by pressing the 

F4 

softkey during device startup.

RUN

ERROR

H1

H2

RUN

ERROR

H1

H2

RUN

ERROR

H1

H2

C

C

RUN

ERROR

H1

H2

C

C

ERROR

RUN

H1

H2

C

C

ERROR

ERROR

RUN

H1

H2

C

C

ERROR

MAN_SICAM_Q100_US.book  Page 371  Wednesday, June 5, 2019  9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments