Siemens SICAM Q100 7KG95 Series Manual Download Page 165

Page: 165 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

165

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

✧

After the parameterization click

Send

The parameters are transmitted to the device but not enabled yet (passive set of parameters).

✧

If you do not want to make any additional settings, continue with the

Activation

of the device configuration

according to section

Activating the Set of Parameters

. If you want to change other settings, enter the

changes and then enable the device configuration as described in section

Activating the Set of

Parameters

NOTE

If Ethernet communication with

Bus protocol IEC 61850

is active (see Chapter 9.3.7.2) and you change

Network type

, the device will restart.

MAN_SICAM_Q100_US.book Page 165 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 165 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: