Siemens SICAM Q100 7KG95 Series Manual Download Page 194

Page: 194 / 448

9 Operation at Use of a PC

9.3 Configuration of the Device

194

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

Parameterizing the Event Recorder

To change the

Event Recorder

, proceed as follows:

✧

In the navigation window, select the

Recording and Reporting

menu and click

Event Recorder

Figure 9-46

Configure Tab, Event Recorders Input/Output Window

✧

Select the respective parameters in the list boxes according to Table 9-14.

✧

After the parameterization click

Send

The parameters are transmitted to the device but not enabled yet (passive set of parameters).

✧

If you do not want to make any additional settings, continue with the

Activation

of the device configuration

according to section

Activating the Set of Parameters

. If you want to change other settings, enter the

changes and then enable the device configuration as described in section

Activating the Set of

Parameters

MAN_SICAM_Q100_US.book Page 194 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 194 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: