manualshive.com logo in svg

Siemens SICAM Q100 7KG95 Series, Manual, Page: 389 / 448

Share
Download
Siemens SICAM Q100 7KG95 Series Manual Download Page 389

14 Technical Data

14.2 Test Data

389

SICAM Q100, 7KG95xx, Device Manual
E50417-H1040-C522-A6, Edition 06.2019

14.2.2

Mechanical Stress Tests

Vibration and Shock Stress during Stationary Operation

Vibration and Shock Stress during Transport

14.2.3

Safety Standards

Standards:

IEC 60068

Oscillation
IEC 60068-2-6 test Fc

Sinusoidal 
10 Hz to 60 Hz: 

0.075 mm amplitude; 60 Hz to 150 Hz: 

1 g acceleration 
Frequency sweep rate 1 octave/min 20 cycles in 3 or-
thogonal axes.

Shock 
IEC 60068-2-27 test Ea

Semi-sinusoidal
5 g acceleration, duration 11 ms, each 3 shocks in both 
directions of the 3 axes

Seismic Vibration
IEC 60068-3-3 test Fc

Sinusoidal 
1 Hz to 8 Hz: 

7.5 mm amplitude (horizontal axis) 

1 Hz to 8 Hz: 

3.5 mm amplitude (vertical axis)

8 Hz to 35 Hz: 2 g acceleration (horizontal axis) 
8 Hz to 35 Hz: 1 g acceleration (vertical axis) 
Frequency sweep 1 octave/min 
1 cycle in 3 orthogonal axes

Standards:

IEC 60068

Oscillation 
IEC 60068-2-6 test Fc

Sinusoidal 
5 Hz to 8 Hz: 

7.5 mm amplitude; 

8 Hz to 150  Hz: 2 g acceleration 
Frequency sweep 1 octave/min 
20 cycles in 3 orthogonal axes

Shock 
IEC 60068-2-27 test Ea

Semi-sinusoidal
15 g acceleration, duration 11 ms,
each 3 shocks (in both directions of the 3 axes)

Continuous Shock
IEC 60068-2-29 test Eb

Semi-sinusoidal 
10 g acceleration, duration 16 ms, 
each 1000 shocks (in both directions of the 3 axes)

Free fall
IEC 60068-2-32 test Ed

0.5 m

Standards: EN 61010
IEC EN 61010-1, IEC EN 61010-2-30

MAN_SICAM_Q100_US.book  Page 389  Wednesday, June 5, 2019  9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Reviews:

No comments