Siemens SICAM Q100 7KG95 Series Manual Download Page 354

Page: 354 / 448

10 Operation at Use of the Display

10.4 Parameterization

354

SICAM Q100, 7KG95xx, Device Manual

E50417-H1040-C522-A6, Edition 06.2019

After the communication parameters have been changed, the device restarts. For this purpose, a prompt
is displayed which you must acknowledge with

Table 10-6

IP Address Settings

Parameter

Default Setting

Setting Range

MAC address

fixed

IP address

192.168.0.55

Any
0.0.0.0 = DHCP

Subnet

255.255.255.0

Any

Gateway

192.168.0.1

Any

Table 10-7

Ethernet Communication Settings

Parameter

Default Setting

Setting Range

Bus protocol

Modbus TCP

none
Modbus TCP
IEC 61850
Both

Ethernet Communication - Modbus TCP Bus Protocol

Access rights for port 502

full

full
read only

Keepalive time

10 s

0 s = switched off
1 s to 65,535 s

Communication monitoring time

600 * 100 ms

0 s = none
100 ms to 6 553 400 ms

Use user port number

No
Yes

User port number

(only settable if

Set user port number

is parameterized with

yes

)

10 000

10 000 to 65 535

Access right for user port
(only settable if

Set user port number

is parameterized with

yes

)

full

full
read only

Ethernet Communication - IEC 61850 Bus Protocol

IED Name

SICAM_Q100_01

read only

Voltage - Deadband

5 %

1 % to 5 % in increments of 1 %

MAN_SICAM_Q100_US.book Page 354 Wednesday, June 5, 2019 9:31 AM

Summary of Contents for SICAM Q100 7KG95 Series

































































































































































































































































































































































































































































Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews:

Siemens SICAM Q100 7KG95 Series, Manual, Page: 354 / 448

Search results

Summary of Contents for SICAM Q100 7KG95 Series

Reviews: