National Instruments DAQ-STC Series Technical Reference Manual Download | Manualshive

Page: 79 / 555

background image

Chapter 2

Analog Input Timing/Control

DAQ-STC Technical Reference Manual

2-50

©

National Instruments Corporation

AI_CONVERT_Original_Pulse

bit: 9

type: Write

in: AI_Personal_Register

address: 77

If AI_CONVERT_Pulse_Timebase is 1, this bit determines the pulsewidth of the CONVERT
and PFI2/CONV signals. The pulsewidth of the CONVERT signals is:

0: Equal to the pulsewidth of the signal used to generate the CONVERT signal, with

the maximum pulsewidth determined by AI_CONVERT_Pulse_Width.

1: Equal to the pulsewidth of the signal used to generate the CONVERT signal.

Related bitfields: AI_CONVERT_Pulse_Timebase, AI_CONVERT_Pulse_Width.

AI_CONVERT_Output_Select

bits: <0..1>

type: Write

in: AI_Output_Control_Register

address: 60

This bit enables and selects the polarity of the CONVERT output signal:

0: High Z.
1: Ground.
2: Enable, active low.
3: Enable, active high.

This bitfield also selects the polarity of the PFI2/CONV output signal, if enabled for output:

0: Active low.
1: Ground.
2: Active low.
3: Active high.

Related bitfields: BD_2_Pin_Dir.

AI_CONVERT_Pulse

bit: 0

type: Strobe

in: AI_Command_1_Register

address: 8

Setting this bit to 1 produces a pulse on the CONVERT and PFI2/CONV output signals, if the
signals are enabled for output and if CONVERT pulses are not blocked. CONVERT pulses
can be blocked by the external gate, the software gate, the start/stop gate, or the SC gate. The
pulsewidths of the output signals are determined by AI_CONVERT_Pulse_Width. This bit is
cleared automatically. This bit is disabled when AI_Configuration_Start is set to 1. Related
bitfields: AI_CONVERT_Output_Select, BD_2_Pin_Dir, AI_CONVERT_Pulse_Width.

AI_CONVERT_Pulse_Timebase

bit: 11

type: Write

in: AI_Personal_Register

address: 77

This bit determines how the pulsewidths of the CONVERT and PFI2/CONV signals are
selected:

0: Selected by AI_CONVERT_Pulse_Width.
1: Selected by AI_CONVERT_Original_Pulse.

Related bitfields: AI_CONVERT_Pulse_Width, AI_CONVERT_Original_Pulse.

«
...
77
78
79
80
81
...
»

Summary of Contents for DAQ-STC Series












































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DAQ-STC Series

Brand: GBD Pages: 68

Brand: Talgil Pages: 14

Brand: Tadao Pages: 2

Brand: VAT Pages: 26

Brand: Eaton Pages: 8

Brand: ABB Pages: 44

Brand: Omega Pages: 2

Brand: Zmotion Pages: 34

iEP-5000G Series

Brand: ASROCK Pages: 2

Brand: Runxin Pages: 4

Brand: Hard Head Pages: 10

Brand: IFM Pages: 41

Brand: Duco Pages: 16

Compact Performance Series

Brand: Festo Pages: 58

Grain PNEG-1509

Brand: GSi Pages: 70

Brand: Junkers Pages: 68

multisio 1D4-4RO ISO

Brand: KBR Pages: 8

Brand: Applied Robotics Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands