National Instruments DAQ-STC Series Technical Reference Manual Download | Manualshive

Page: 223 / 555

background image

Chapter 3

Analog Output Timing/Control

©

National Instruments Corporation

3-61

DAQ-STC Technical Reference Manual

AO_Mode_3_Register
AO_Output_Control_Register
AO_Personal_Register
AO_START_Select_Register
AO_Trigger_Select_Register

Setting this bit to 1 also clears all of the status bits and interrupts related to analog output,
except those associated with the data FIFO. This bit is cleared automatically.

AO_Software_Gate

bit: 1

type: Write

in: AO_Mode_3_Register

address: 70

This bit controls the software gate, which you can use to pause an analog output operation:

0: Enable operation.
1: Pause operation.

This bit is not supported on the first revision of the DAQ-STC, and must be set to 0. See
Appendix D,

DAQ-STC Revision History

, for DAQ-STC revision information.

AO_Source_Divide_By_2

bit: 4

type: Write

in: Clock_and_FOUT_Register

address: 56

This bit determines the frequency of the internal timebase AO_IN_TIMEBASE1:

0: Same as IN_TIMEBASE.
1: IN_TIMEBASE divided by two.

AO_START_Edge

bit: 5

type: Write

in: AO_START_Select_Register

address: 66

This bit enables edge detection of the START trigger:

0: Disabled.
1: Enabled.

This bit is currently not supported, and it must be set to 0.

AO_START_Interrupt_Ack

bit: 11

type: Strobe

in: Interrupt_B_Ack_Register

address: 3

Setting this bit to 1 clears AO_START_St and acknowledges the START interrupt (in either
interrupt bank) if the START interrupt is enabled. This bit is cleared automatically. This
bitfield is not currently supported.

«
...
221
222
223
224
225
...
»

Summary of Contents for DAQ-STC Series












































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DAQ-STC Series

Brand: ABB Pages: 139

Brand: ABB Pages: 28

Brand: ABB Pages: 59

Brand: K&K Pages: 6

Brand: ZirbenLüfter Pages: 36

Brand: Harsco Industrial Pages: 57

Brand: Samson Pages: 20

Brand: National Instruments Pages: 2

Brand: RADEMACHER Pages: 48

Brand: M-system Pages: 13

Brand: GI.BI.DI Pages: 60

DuoControl Signal 111

Brand: Tormatic Pages: 3

Brand: Petique Pages: 44

CWDM-CR-B Series

Brand: Lantronix Pages: 19

Brand: Netafim Pages: 4

Brand: TREND Pages: 12

Bell & Gossett Technologic PPS

Brand: Xylem Pages: 20

Brand: Logitech Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands