Mitsubishi Electric FR-F800, Instruction Manual

Page: 390 / 834

(M) Monitor display and monitor output signal Parameters
5 - 228
41 141 FB Speed detection Output when the actual motor rotations
per minute (estimated rotations per
minute) reaches Pr. 42 (Pr. 50.
Pr. 42, Pr. 50 5-234
42 142 FB2 Second speed detection
45 145 RUN3
Inverter running and start
command is ON Output while the inverter is running and
the start command is ON.
⎯
5-232
46 146 Y46
During deceleration at
occurrence of power
failure (retained until
release)
Output after the power-failure
deceleration function operates.
(Retained until cancelled.)
Pr. 261 to
Pr. 266
5-426
47 147 PID
During PID control
activated
Output during PID control.
Pr. 127 to
Pr. 134, Pr. 575
to Pr. 577
5-347
48 148 Y48 PID deviation limit
Output when the absolute deviation
value exceeds the limit value.
Pr. 127 to
Pr. 134, Pr. 553,
Pr. 554
5-347
49 149 Y49
During pre-charge
operation
Output during pre-charge operation.
Pr. 127 to
Pr. 134, Pr. 241,
Pr. 553, Pr. 554,
Pr. 575 to
Pr. 577, Pr. 753
to Pr. 769, C42
to C45
5-379
50 150 Y50
During second pre-
charge operation
51 151 Y51 Pre-charge time over
Output when the pre-charge operation
reaches the time limit set in Pr. 764 or Pr.
769.
52 152 Y52
Second pre-charge time
over
53 153 Y53 Pre-charge level over
Output when the measured value before
reaching the ending time during pre-
charge operation is higher than the
detection level set in Pr. 763 or Pr. 768.
54 154 Y54
Second pre-charge level
over
57 157 IPM During PM motor control
Output while the control method is PM
motor control. Pr. 71, Pr. 80,
Pr. 998
5-45
64 164 Y64 During retry Output during retry processing. Pr. 65 to Pr. 69 5-159
65 165 Y65
Emergency drive in
operation
Output during emergency drive
operation
Pr. 514, Pr. 515,
Pr. 523, Pr. 524,
Pr. 1013
5-162
66 166 ALM3
Fault output during
emergency drive Output when a fault occurs during
emergency drive operation.
67 167 Y67
Power failure signal
Output when the power failure time
deceleration-to-stop function is activated
during output shutoff due to power
failure or undervoltage.
Pr. 261 to
Pr. 266
5-426
68 168 EV
24 V external power
supply operation
Output while operating with a 24 V
power supply input from an external
source.
⎯
2-57
70 170 SLEEP PID output interruption
Output during PID output suspension
function operation.
Pr. 127 to
Pr. 134, Pr. 575
to Pr. 577
5-347
71 171 RO1
Commercial power
supply side motor 1
connection
Output depending on the motor drive
conditions when the multi-pump
function is used.
Pr. 575 to
Pr. 591
5-386
72 172 RO2
Commercial power
supply side motor 2
connection RO2
73 173 RO3
Commercial power
supply side motor 3
connection RO3
74 174 RO4
Commercial power
supply side motor 4
connection
75 175 RIO1
Inverter side motor 1
connection RIO1
76 176 RIO2
Inverter side motor 2
connection RIO2
77 177 RIO3
Inverter side motor 3
connection RIO3
78 178 RIO4
Inverter side motor 4
connection RIO4
Setting
Signal
name
Function Operation
Related
parameter Refer to
page
Positive
logic
Negative
logic
Tab. 5-101: Output terminal function assignment (2)