Lucent Technologies PARTNER Advanced Communications System Release 1.0 Programming And Use Instructions Download Page 266 | Manualshive

Page: 266 / 365

background image

System Reset—Programming Saved
(#728)

Description

This System Programming procedure resets the system while retaining the
currently programmed settings. Reset the system only when advised to do so by
technical support personnel.

Related Features

After a power failure or system reset:

Night Service Button (#503)

Station Lock

return to the status (on or

off) that they were in immediately prior to the power failure or system reset.

The

VMS Cover button

button return to the status (on or off)

determined by the programmed setting of

Automatic VMS Cover (#310)

and

Automatic Extension Privacy (#304)

, respectively. For example, If

Automatic Extension Privacy is Assigned and the Privacy button is on
when a system reset occurs, the Privacy button will be on again after the
system reset. However, if Automatic Extension Privacy is Not Assigned
and the Privacy button is on when a system reset occurs, the Privacy
button will be off after the system reset.

All other active features at an extension are reset to the default settings.
For example, if an extension has calls forwarded to another extension,
resetting the system turns off

Call Forwarding

(if the feature is

programmed on a button with lights, the reset also turns off the light for
the Call Forwarding button).

A successful use of

Restore Programming (#125)

causes a System

Reset—Programming Saved (#728) to occur.

The information stored in the

Save Number Redial (F04)

and the

Number Redial (F05)

buffers is lost when a System Reset—Programming

Saved (#728) occurs.

Considerations

Resetting the system disconnects all active calls.

This procedure is skipped in the sequence of programming procedures
when cycling. To use this procedure, enter the code directly.

The system reset begins immediately and takes only a few seconds.

You cannot interrupt the reset process or use any telephones in the system
during the reset process.

All of the system and telephone programming settings that were in effect
before the power failure or down period are retained (except those
mentioned in the “Related Features” section above); they do not revert to the
default settings.

System Reset—Programming Saved (#728)

5-173

«
...
264
265
266
267
268
...
»

Summary of Contents for PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Reviews:

No comments

Related manuals for PARTNER Advanced Communications System Release 1.0

Brand: Yamaha Pages: 14

Brand: Yamaha Pages: 28

Brand: Yamaha Pages: 109

Brand: Yamaha Pages: 3

Brand: Start Shaphon Pages: 66

Brand: Hioki Pages: 32

RealPresence Group 500 systems

Brand: Polycom Pages: 2

Brand: BriarTek Pages: 2

Audio Everywhere

Brand: Listen Technologies Pages: 2

Leasam BM2-7D-4Z

Brand: ActronControls Pages: 2

Brand: Sanyo Pages: 4

Brand: Sanyo Pages: 13

Brand: Sanyo Pages: 13

Brand: Sanyo Pages: 13

Brand: Sanyo Pages: 15

TS-D1000 Series

Brand: Toa Pages: 44

Brand: Speakerbus Pages: 2

KMD-5540 CommTalk

Brand: KMC Controls Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands