Lucent Technologies PARTNER Advanced Communications System Release 1.0 Programming And Use Instructions Download Page 121 | Manualshive

Page: 121 / 365

background image

For information about using Option 3, “Backup Alarm Cleared,” see “Clearing a
Backup-Failure Alarm” in Chapter 6, “Troubleshooting.”

Inserting or Removing a PC Card

1.

If the system has power, do one of the following to turn off the power:

5-Slot carrier: Move the On/Off switch to the “Off” position (“O”).
2-Slot carrier or Stand-Alone PARTNER ACS processor module: Unplug
the power cord from the power jack.

2.

Insert a valid Backup/Restore PC Card in Slot 2 of the PARTNER ACS
processor module.

3.

Turn on the system power by doing one of the following:

5-Slot carrier: Move the On/Off switch to the “On” position (“I”).
2-Slot carrier or Stand-Alone PARTNER ACS processor module: Plug
the power cord into the power jack.

Using

Use Option 3 to clear Backup-Failure Alarms. See “Clearing a Backup-Failure
Alarm” in Chapter 6, “Troubleshooting.”

5-28

Backup Programming—Automatic (#123)

«
...
119
120
121
122
123
...
»

Summary of Contents for PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Reviews:

No comments

Related manuals for PARTNER Advanced Communications System Release 1.0

Univerge SV8100

Brand: NEC Pages: 2

Brand: Lathem Pages: 4

Brand: TANDBERG Pages: 65

Brand: Discount Car Stereo Pages: 4

Brand: Danfoss Pages: 8

Brand: Zonex Pages: 28

Brand: Globalmediapro Pages: 11

Brand: Leb Electronics Pages: 6

Brand: SKF Pages: 63

Brand: Hama Pages: 45

Brand: babala Pages: 30

Brand: Scott Pages: 29

Brand: SOUNDMASTER Pages: 110

Brand: RCA Pages: 35

Brand: Kenwood Pages: 24

Brand: Kenwood Pages: 21

Brand: Kenwood Pages: 28

KMR-700U - Radio / Digital Player

Brand: Kenwood Pages: 35

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands