Lucent Technologies PARTNER Advanced Communications System Release 1.0 Programming And Use Instructions Download Page 131

Page: 131 / 365

To program another extension, press

until the extension

number shows on the display. Then repeat Step 3.

Select another procedure or exit programming mode.

5-38

Call Waiting (#316)

Summary of Contents for PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Search results

Summary of Contents for PARTNER Advanced Communications System Release 1.0

Reviews:

Related manuals for PARTNER Advanced Communications System Release 1.0

Brands by name

Popular brands

Lucent Technologies PARTNER Advanced Communications System Release 1.0, Programming And Use Instructions

Search results

Summary of Contents for PARTNER Advanced Communications System Release 1.0

Reviews:

Related manuals for PARTNER Advanced Communications System Release 1.0

Brands by name

Popular brands