Home
/
Lucent Technologies
/
PARTNER Advanced Communications System Release 1.0
/
Programming And Use Instructions

Lucent Technologies PARTNER Advanced Communications System Release 1.0, Programming And Use Instructions

Share

Page: 329 / 365

Lucent Technologies PARTNER Advanced Communications System Release 1.0 Programming And Use Instructions Download Page 329

to the equipment. For personal injury caused by Lucent Technologies’
negligence, Lucent Technologies’ liability shall be limited to proven damages to
person. No action or proceeding against Lucent Technologies or its affiliates or
suppliers may be commenced more than twenty-four (24) months after the
cause of action accrues. THIS PARAGRAPH SHALL SURVIVE FAILURE OF AN
EXCLUSIVE REMEDY.

Product Ordering Information

Reference Materials

In addition to this guide, the following materials are available (the order numbers
are in parentheses):

PARTNER Advanced Communications System Planner (518-456-051)
provides the forms needed to plan and record how your system and
telephones are to be programmed.

PARTNER Advanced Communications Installation (518-456-052)
provides instructions for installing the system.

User Instruction Cards (518-455-340) contains basic instructions for
using system phones.

PARTNER-34D Programming Overlay (847531696) helps with System
Programming from a PARTNER-34D phone.

PARTNER-18D Programming Overlay (847531688) helps with System
Programming from a PARTNER-18D phone.

MDW 9030P Wireless Pocketphone Installation and Use (503-801-160)
explains how to install and use the MDW 9030P pocketphone.

MDW 9030P Wireless Pocketphone Quick Reference (503-801-161)
contains basic information for using the MDW 9030P pocketphone.

MLC-6 Cordless Telephone Installation (999-506-143) explains how to
install the MLC-6 cordless telephone.

MLC-6 Cordless Telephone Quick Reference (999-506-146) contains
basic information for using the MLC-6 cordless telephone.

PARTNER MAIL VS Voice Messaging System Release 3 Installation and
Programming (518-322-105) provides instructions for installing,
programming, and maintaining your PARTNER MAIL VS system.

PARTNER MAIL VS Voice Messaging System Release 3 Planning Forms
(585-322-504) provides the forms needed to plan and record how your
PARTNER MAIL VS system is to be programmed.

Using the PARTNER MAIL VS Voice Messaging System Release 3
(518-322-106) contains instructions for using the PARTNER MAIL VS
system.

PARTNER MAIL Voice Messaging System Release 3 Planning,
Installation, and Use (585-322-516) provides instructions for planning,
installing, programming, and maintaining your PARTNER MAIL system.

B-4

Maintenance

«
...
327
328
329
330
331
...
»

Summary of Contents for PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands