Lucent Technologies PARTNER Advanced Communications System Release 1.0 Programming And Use Instructions Download Page 316 | Manualshive

Page: 316 / 365

background image

Display Shows “Backup Failed:Check Card”
in System Programming Mode

Possible Cause 1: The Backup/Restore PC Card was removed while the backup was in
progress.

What to do:  Check to see whether the PC Card was removed.  If it was not, go to Possible
Cause 2.  If it was, power down the system, reinsert the PC Card, and reapply power to the
system.  Restart the

Backup Programming—Manual (#124)

procedure.

Possible Cause 2: The Backup/Restore PC Card or the PARTNER ACS processor module
is corrupted.

What to do: Try the backup again using the backup procedure—

Backup

Programming—Manual (#124

).

If the backup completes successfully, the problem is solved.

If the backup fails again, try to determine whether the problem is a corrupted PC
Card or a corrupted processor module by trying the backup twice using two different
Backup/Restore PC Cards:

—

If the system will not write to either PC Card, the processor module is
probably corrupted; call the hotline*.

—

If the system writes to one of the PC Cards, the original PC Card is
corrupted. See Table B-1 in Appendix B for the information about
ordering a new Backup/Restore PC Card.

Display Shows “Backup Failed:SystemBusy”
in System Programming Mode

Possible Cause: Changes were being made to system programming or central telephone
programming while a backup was in progress.

What to do: Try

Backup Programming—Manual (#124)

later when the system is idle or

during nonbusiness hours.

*

In the continental U.S., help is available at 1 800 628-2888. Outside the continental U.S., call your
Lucent Technologies Representative or local Authorized Dealer.

Troubleshooting

6-21

«
...
314
315
316
317
318
...
»

Summary of Contents for PARTNER Advanced Communications System Release 1.0














































































































































































































































































































































































Reviews:

No comments

Related manuals for PARTNER Advanced Communications System Release 1.0

Brand: Balboa Pages: 74

Brand: Panasonic Pages: 89

Brand: Absima Pages: 5

MorphoAccess VP MD

Brand: Idemia Pages: 29

Brand: Hame Pages: 26

Brand: Vansco Pages: 11

Brand: Ruida Technology Pages: 35

Brand: Toa Pages: 12

NOTIFIER CBC-CLASS 1

Brand: Pittway Pages: 20

AIR ADJUST 2940

Brand: Yetter Pages: 64

AeGIS 8000 Series

Brand: PACH & COMPANY Pages: 14

PressureMAT PMAT2

Brand: PendoTECH Pages: 48

Brand: B&R Industries Pages: 16

Brand: Boss Audio Systems Pages: 17

Brand: Boss Audio Systems Pages: 9

Brand: Curtis Pages: 1

Brand: Raven Pages: 10

Brand: Advanced Native Technologies Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands