manualshive.com logo in svg

Kyocera TASKALFA 300I, Service Manual

The Kyocera TASKALFA 300I is a multifunctional printer designed to enhance productivity in your workplace. Ensure seamless operation with our comprehensive User Manual, available for free download on our website. Explore advanced features, troubleshoot issues, and optimize your device's performance effortlessly with this user-friendly manual.

Share
Download
background image

2K5

1-4-37

(6) A black line appears longitudinally.

(7) A black line appears laterally.

(8) One side of the copy image is darker than the other.

(9) Black dots appear on the image.

Copy example

Causes

Check procedures/corrective measures

Dirty platen.

Clean the platen.

Dirty or flawed drum.

Perform the drum refresh operation. If the drum is flawed, 
replace the drum unit (see page 1-5-31).

Deformed or worn cleaning blade.

Replace the drum unit (see page 1-5-31).

Dirty scanner mirror.

Clean the scanner mirror.

Dirty main charger wire.

Clean the wire or, if it is extremely dirty, replace it (see page 
1-5-33).

Copy example

Causes

Check procedures/corrective measures

Flawed drum.

Replace the drum unit (see page 1-5-31).

Dirty developing section.

Clean any part contaminated with toner in the developing 
section.

Leaking main charger housing.

Clean the main charger wire and grid.

Leaking separation electrode.

Clean the separation electrode.

Copy example

Causes

Check procedures/corrective measures

Dirty main charger wire.

Clean the wire or, if it is extremely dirty, replace it (see page 
1-5-33).

Defective exposure lamp.

Check if the exposure lamp light is distributed evenly. If not, 
replace the exposure lamp (see page 1-5-15).

Copy example

Causes

Check procedures/corrective measures

Dirty or flawed drum.

Perform the drum refresh operation. If the drum is flawed, 
replace the drum unit (see page 1-5-31).

Dirty platen.

Clean the platen.

Deformed or worn cleaning blade.

Replace the drum unit (see page 1-5-31).

Dirty drum separation claws.

Clean the drum separation claws.

Dirty the heat roller separation claws.

Clean the heat roller separation claws.

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

CAB A Series Programming Manual preview
A Series
Brand: CAB Pages: 263
Canon Sure shot 80 tele User Manual preview
Sure shot 80 tele
Brand: Canon Pages: 24
Canon iPF720 - imagePROGRAF Color Inkjet Printer Brochure & Specs preview
iPF720 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 8
Canon i475D Series Setup Instructions preview
i475D Series
Brand: Canon Pages: 2
Samsung ML-6050 Manual Del Usuario preview
ML-6050
Brand: Samsung Pages: 82
Samsung ML-2525 Datasheet preview
ML-2525
Brand: Samsung Pages: 2
Partner RP-100-300II User Manual preview
RP-100-300II
Brand: Partner Pages: 9
Xerox Phaser 6300 Service Manual preview
Phaser 6300
Brand: Xerox Pages: 13
Xerox Phaser 6120 Reference Manual preview
Phaser 6120
Brand: Xerox Pages: 214
Cardco LQ1/1 Operating Manual preview
LQ1/1
Brand: Cardco Pages: 28
Lexmark C53x Clearing Jams Manual preview
C53x
Brand: Lexmark Pages: 6
Riso HC5500T User Manual preview
HC5500T
Brand: Riso Pages: 66
Ricoh Aficio 120 User Manual preview
Aficio 120
Brand: Ricoh Pages: 37
Oce im2330 Network Administration Manual preview
im2330
Brand: Oce Pages: 76
Lexmark C925 User Manual preview
C925
Brand: Lexmark Pages: 221
Xante Ilumina GL User Manual preview
Ilumina GL
Brand: Xante Pages: 106
Riso MZ790U Instruction Manual preview
MZ790U
Brand: Riso Pages: 266
Yamaha YSP10 Service Information preview
YSP10
Brand: Yamaha Pages: 120

Brands by name

Popular brands

Load more brands