Kyocera TASKALFA 300I Service Manual Download Page 141 | Manualshive

Page: 141 / 408

background image

2K5

1-3-105

RA (Stateless) Settings

1. Press [Next] of Network and then [Next] of TCP/IP

Setting.

2. Press [Next] of IPv6.
3. Press [Change] of RA(Stateless).
4. Press [On] or [Off] of RA (Stateless).
5. Press [OK].
6. After changing the setting, restart the system or

turn the machine OFF and then ON again.

DHCP (IPv6) Settings

1. Press [Next] of Network and then [Next] of TCP/IP

Setting.

2. Press [Next] of IPv6.
3. Press [Change] of DHCP.
4. Press [On] or [Off] of DHCP.
5. Press [OK].
6. After changing the setting, restart the system or

turn the machine OFF and then ON again.

NetWare Setup

1. Press [Next] of Network and then [Change] of Net-

Ware.

2. Press [On].
3. Press the key for the frame type you want to use.
4. Press [OK].
5. After changing the setting, restart the system or

turn the machine OFF and then ON again.

AppleTalk Setup

1. Press [Next] of Network and then [Change] of

AppleTalk.

2. Press [On] or [Off].
3. Press [OK].
4. After changing the setting, restart the system or

turn the machine OFF and then ON again.

WSD Scan Setup

1. Press [Next] of Network and then [Change] of WSD

Scan.

2. Press [On] or [Off].
3. Press [OK].
4. After changing the setting, restart the system or

turn the machine OFF and then ON again.

WSD Print Setup

1. Press [Next] of Network and then [Change] of WSD

Print.

2. Press [On] or [Off].
3. Press [OK].
4. After changing the setting, restart the system or

turn the machine OFF and then ON again.

SSL Setup

1. Press [Next] of Network, [Next] of Secure Protocol,

and then [Next] of SSL.

2. Press [On] or [Off].
3. Press [OK].
4. After changing the setting, restart the system or

turn the machine OFF and then ON again.

IPP Security Setup

1. Press [Next] of Network, [Next] of Secure Protocol,

and then [Change] of IPP Security.

2. Press [IPP over SSL Only] or [IPP or IPP over

SSL].

3. Press [OK].
4. After changing the setting, restart the system or

turn the machine OFF and then ON again.

HTTP Security Setup

1. Press [Next] of Network, [Next] of Secure Protocol,

and then [Change] of HTTPS Security.

2. Press [HTTP or HTTPS] or [HTTPS Only].
3. Press [OK].
4. After changing the setting, restart the system or

turn the machine OFF and then ON again.

LDAP Security Setup

1. Press [Next] of Network, [Next] of Secure Protocol,

and then [Change] of LDAP Security.

2. Press [Off], [LDAP over SSL] or [LDAPv3/TLS].
3. Press [OK].
4. After changing the setting, restart the system or

turn the machine OFF and then ON again.

IPSec Setting

1. Press [Next] of Network, and then [Change] of

IPSec.

2. Press [On].
3. Press [OK].
4. After changing the setting, restart the system or

turn the machine OFF and then ON again.

LAN Interface Setup

1. Press [Next] of Network and then [Change] of LAN

Interface.

2. Select [Auto], [10BASE-T Half], [10BASE-T Full],

[100BASE-TX Half] or [100BASE-TX Full] as the
LAN interface.

3. Press [OK].
4. After changing the setting, restart the system or

turn the machine OFF and then ON again.

«
...
139
140
141
142
143
...
»

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Panafax UF-7000

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 68

Brand: Panasonic Pages: 120

Brand: Panasonic Pages: 100

KX-MB781 - B/W Laser - All-in-One

Brand: Panasonic Pages: 96

Brand: Panasonic Pages: 130

Brand: Oki Pages: 210

Brand: Panasonic Pages: 77

Brand: Panasonic Pages: 402

Brand: Panasonic Pages: 54

Workio DP-8016P

Brand: Panasonic Pages: 88

Brand: Panasonic Pages: 60

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 341

Brand: Samsung Pages: 8

CLX2160N - Color Laser - All-in-One

Brand: Samsung Pages: 118

CLX 3160FN - Color Laser - All-in-One

Brand: Samsung Pages: 142

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands