manualshive.com logo in svg

Kyocera TASKALFA 300I, Service Manual

The Kyocera TASKALFA 300I is a multifunctional printer designed to enhance productivity in your workplace. Ensure seamless operation with our comprehensive User Manual, available for free download on our website. Explore advanced features, troubleshoot issues, and optimize your device's performance effortlessly with this user-friendly manual.

Share
Download
background image

2K5

1-3-50

U155

Checking sensors for toner
Description

Displays the on-off status of each sensor or switch related to toner.

Purpose

To check if the sensors and switches operate correctly.

Method

1. Press the start key.
2. Turn each switch on and off manually to check the status.

When the on-status of a switch is detected, that switch is displayed in reverse.

3. To stop motor driving, press [MOTOR ON] again.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U157

Checking the developing drive time
Description

Displays the developing drive time for checking, which is used as a reference when correcting the toner con-
trol.

Purpose

To check the developing drive time after replacing the developing unit.

Method

1. Press the start key. The developing drive time is displayed in minutes.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U158

Checking the developing count
Description

Displays the developing count for checking.

Purpose

To check the developing count after replacing the developing unit.

Method 

1. Press the start key. The developing counter count is displayed.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Switches and sensors

DEVELOPER SENSOR

Toner sensor (TNS)

CONTAINER SET

Toner container detection switch (TCDSW)

CONTAINER SENSOR

Toner container sensor (TCS)

DISPOSAL TANK SENSOR

Overflow sensor (OFS)

MOTOR

The toner feed clutch (TFCL) and the paper feed motor (PFM) 
are turned on.

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Canon iR3245 Troubleshooting Manual preview
iR3245
Brand: Canon Pages: 300
Canon iR3245 Network Manual preview
iR3245
Brand: Canon Pages: 288
Canon iR3245 User Manual preview
iR3245
Brand: Canon Pages: 58
Canon iR1510 Quick Start Manual preview
iR1510
Brand: Canon Pages: 30
Canon Sure shot 80 tele User Manual preview
Sure shot 80 tele
Brand: Canon Pages: 24
Canon iPF720 - imagePROGRAF Color Inkjet Printer Brochure & Specs preview
iPF720 - imagePROGRAF Color Inkjet Printer
Brand: Canon Pages: 8
Canon i475D Series Setup Instructions preview
i475D Series
Brand: Canon Pages: 2
Partner RP-700 User Manual preview
RP-700
Brand: Partner Pages: 34
Partner RP-330 Technical Manual preview
RP-330
Brand: Partner Pages: 81
Riso RP3100AW User Manual preview
RP3100AW
Brand: Riso Pages: 208
Olivetti d-Copia 45 Operation Manual preview
d-Copia 45
Brand: Olivetti Pages: 246
Ricoh IM C6000 Series Quick Reference Copy Manual preview
IM C6000 Series
Brand: Ricoh Pages: 2
Epson C382011B - Stylus Pro 7500 Color Inkjet Printer Warranty preview
C382011B - Stylus Pro 7500 Color Inkjet Printer
Brand: Epson Pages: 8
Epson C390999 - TM T90 Color Thermal Line Printer Development Manual preview
C390999 - TM T90 Color Thermal Line Printer
Brand: Epson Pages: 22
Epson C383001 - Stylus 777 Color Inkjet Printer Specification Sheet preview
C383001 - Stylus 777 Color Inkjet Printer
Brand: Epson Pages: 2
Epson C31C390A8931 - TM T90 Two-color Thermal Line Printer User Manual preview
C31C390A8931 - TM T90 Two-color Thermal Line Printer
Brand: Epson Pages: 60
Epson ColorPage EPL-C8200 Setup Manual preview
ColorPage EPL-C8200
Brand: Epson Pages: 90
Epson CaptureOne TM-S1000 Installation Manual preview
CaptureOne TM-S1000
Brand: Epson Pages: 8

Brands by name

Popular brands

Load more brands