manualshive.com logo in svg

Kyocera TASKALFA 300I, Service Manual

The Kyocera TASKALFA 300I is a multifunctional printer designed to enhance productivity in your workplace. Ensure seamless operation with our comprehensive User Manual, available for free download on our website. Explore advanced features, troubleshoot issues, and optimize your device's performance effortlessly with this user-friendly manual.

Share
Download
background image

2K5-1

1-6-1

1-6 Requirements on PWB Replacement

1-6-1  Upgrading the firmware

Follow the procedure below to upgrade the firmware of main PWB, engine PWB and MMI.

Firmware upgrading requires the following tools:

USB memory

Procedure

1. Perform maintenance item U000 (mainte-

nance report output) and check U019 ROM 
version.

2. Press the power key on the operation panel 

to off. Make sure that the power indicator 
and the memory indicator are off before 
turning off the main power switch. And then 
unplug the power cable from the wall outlet.

3. Insert the USB memory in the USB memory 

slot.

4. Insert the power plug and turn the main 

power switch on. Upgrading firmware starts.

Caution:

Never turn the main power switch off during 
upgrading.

Figure 1-6-1

5. [100% Completed] is displayed on the touch 

panel when upgrading is complete.

6. Turn the main power switch off and unplug 

the power cable from the wall outlet.

7. Remove the USB memory from the USB 

memory slot.

8. Insert the power plug and turn the main 

power switch on.

USB memory

USB memory slot

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Xerox 220 Getting Started preview
220
Brand: Xerox Pages: 48
Oce 3155 System Data preview
3155
Brand: Oce Pages: 4
Panasonic KX-PS8000 Reference Manual preview
KX-PS8000
Brand: Panasonic Pages: 155
Panasonic KX-MB2061 Operating Instructions Manual preview
KX-MB2061
Brand: Panasonic Pages: 160
Xerox 5700 Series Manual preview
5700 Series
Brand: Xerox Pages: 25
GCC Technologies Elite 12N Network Manual preview
Elite 12N
Brand: GCC Technologies Pages: 63
GCC Technologies Elite XL-1208 Supplementary Manual preview
Elite XL-1208
Brand: GCC Technologies Pages: 9
GCC Technologies Elite XL User Manual preview
Elite XL
Brand: GCC Technologies Pages: 199
Xerox DocuColor 6060 Recommended Materials List preview
DocuColor 6060
Brand: Xerox Pages: 4
Lexmark 7016-630 Service Manual preview
7016-630
Brand: Lexmark Pages: 455
Pandigital ZINK PANPRINT01 Quick Start Manual preview
ZINK PANPRINT01
Brand: Pandigital Pages: 2
Kyocera FS-C8008N Operation Manual preview
FS-C8008N
Brand: Kyocera Pages: 157
Canon PIXMA MX892 Getting Started Manual preview
PIXMA MX892
Brand: Canon Pages: 4
Konica Minolta bizhub C250i Quick Manual preview
bizhub C250i
Brand: Konica Minolta Pages: 61
Quest Payment Systems Donation Point Even Quick Start Manual preview
Donation Point Even
Brand: Quest Payment Systems Pages: 2
Ricoh Lanier AP206 Setup Manual preview
Lanier AP206
Brand: Ricoh Pages: 406
Nitto Denko DURA PRINTER SI600 Instruction Manual preview
DURA PRINTER SI600
Brand: Nitto Denko Pages: 174
Monarch 9493 9493 Mounting Instructions preview
9493 9493
Brand: Monarch Pages: 8

Brands by name

Popular brands

Load more brands