Kyocera TASKALFA 300I Service Manual Download Page 92 | Manualshive

Page: 92 / 408

background image

2K5

1-3-56

U206

Setting the presence or absence of the coin vender
Description

Sets the presence or absence of the optional coin vender. Also sets the details for coin vender operation, such
as mode and unit price.
This is an optional device which is currently supported only by Japanese specification machines, so no setting
is necessary.

U207

Checking the operation panel keys
Description

Checks operation of the operation panel keys.

Purpose

To check operation of all the keys and LEDs on the operation panel.

Method

1. Press the start key. The screen for executing is displayed.
2. COUNT0 is displayed and the leftmost LED on the operation panel lights.
3. As the keys lined up in the same line as the lit indicator are pressed in the order from the top to the bot-

tom, the figure shown on the touch panel increases in increments of 1. When all the keys in that line are
pressed and if there are any LEDs corresponding to the keys in the line on the immediate right, the top
LED in that line will light.

4. When all the keys on the operation panel have been pressed, all the LEDs light for up to 10 seconds.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U221

Setting the USB host lock function
Description

Specifies ON/OFF the USB host lock function. Setting this to ON causes the machine to be unable to recog-
nize the device connected to the USB host.

Purpose

Set according to the preference of the user.

Method

1. Press the start key.
2. Select the item.

Setting

1. Select [ON] or [OFF].

Initial setting: OFF

2. Press the start key. The setting is set.
3. Turn the main power switch off and on.

U222

Setting the IC card type
Description

Sets the IC card type.
This is an optional device which is currently supported only by Japanese specification machines, so no setting
is necessary.

Maintenance

item No.

Description

Display

Description

USB HOST LOCK

USB host lock function ON/OFF setting

Display

Description

ON

USB host lock function ON

OFF

USB host lock function OFF

«
...
90
91
92
93
94
...
»

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Brand: Oki Pages: 137

Brand: Samsung Pages: 322

Brand: Samsung Pages: 340

Brand: Samsung Pages: 349

Brand: Samsung Pages: 330

Brand: Samsung Pages: 315

Brand: Samsung Pages: 2

Brand: Samsung Pages: 2

Brand: Samsung Pages: 232

Brand: Samsung Pages: 42

SCX-6545N Series

Brand: Samsung Pages: 468

Brand: Samsung Pages: 196

SCX4521F - B/W Laser - All-in-One

Brand: Samsung Pages: 120

7300DX - Phaser Color Laser Printer

Brand: Xerox Pages: 14

MAGICARD 300plus

Brand: Ultra electronics Pages: 45

Brand: Oki Pages: 255

Bravo se Disc Publisher

Brand: Primera Pages: 58

Brand: Oki Pages: 204

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands