Kyocera TASKALFA 300I Service Manual Download Page 55 | Manualshive

Page: 55 / 408

background image

2K5

1-3-19

U021

Initializing counters and mode settings
Description

Initializes all settings, except those pertinent to the type of machine, namely each counter, service call history
and mode setting. Also initializes backup RAM according to region specification selected in maintenance item
U252 Setting the destination.
Refer to *1 of the maintenance mode item list about the item initialized.

Purpose

To return the machine settings to their factory default.

Method

1. Press the start key.
2. Press [EXECUTE] on the touch panel.
3. Press the start key. All data other than that for adjustments due to variations between machines is initial-

ized based on the destination setting.

4. Turn the main power switch off and on.

An error code is displayed in case of an initialization error.
When ERROR 09 occurred, turn main power switch off then on, format the hard disk using maintenance
item U024, and execute initialization using maintenance item U021. For other errors occurred, turn main
power switch off then on, and execute initialization using maintenance item U021.

Error codes

U024

HDD formatting
Description

Initializes the HDD.
In addition, the following settings are also initialized by initializing the HDD.
System menu (user login administration, job accounting, address book, one-touch keys and document box
etc.), shortcuts and panel programs
Initializing the HDD will cause installed applications to be deleted. Reinstall applications as necessary after
initializing the HDD.

Purpose

To initialize the HDD when replacing the HDD after shipping.

Method

1. Press the start key.
2. Press [EXECUTE] on the touch panel.
3. Press the start key to initialize the hard disk.
4. Turn the main power switch off and on.

Maintenance

item No.

Description

Codes

Description

ERROR 01

Configuration initialization error

ERROR 02

Counter initialization error

ERROR 03

One-touch initialization error

ERROR 04

Panel program initialization error

ERROR 05

Event log initialization error

ERROR 06

Account initialization error

ERROR 07

Address book initialization error

ERROR 08

Department initialization error

ERROR 09

Document box initialization error

ERROR 0a

Permissibility initialization error

ERROR 0b

Job log initialization error

ERROR 20

Engine initialization error

ERROR 40

Scanner initialization error

«
...
53
54
55
56
57
...
»

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Pixma MG2400 Series

Brand: Canon Pages: 2

Brand: IBM Pages: 16

Brand: DataCard Pages: 17

Brand: DataCard Pages: 24

Brand: Xerox Pages: 8

Brand: Panasonic Pages: 32

Brand: Oce Pages: 192

Brand: Oce Pages: 22

Brand: Oce Pages: 41

Brand: Oce Pages: 28

Brand: Oce Pages: 6

Brand: QMS Pages: 104

Brand: Oce Pages: 386

Brand: Oce Pages: 2

Brand: Oce Pages: 27

Brand: Oce Pages: 324

Brand: Xerox Pages: 262

Brand: Oce Pages: 686

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands