Kyocera TASKALFA 300I Service Manual Download

Page: 91 / 408

2K5

1-3-55

U203

Checking DP operation
Description

Simulates the original conveying operation separately in the DP.

Purpose

To check the DP operation.

Method

1. Press the start key.
2. Place an original in the DP if running this simulation with paper.
3. Select the item to be operated.

4. Press the start key. The operation starts.
5. To stop continuous operation, press the stop key.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U204

Setting the presence or absence of a key card or key counter
Description

Sets the presence or absence of the optional key card or key counter.

Purpose

To run this maintenance item if a key card or key counter is installed.

Method

1. Press the start key.
2. Select the item to be set. The setting screen for the selected item is displayed.

Setting: [KEY-DEVICE]

1. Select the optional counter to be installed.

Initial setting: OFF

2. Press the start key. The setting is set.
3. Turn the main power switch off and on.

Setting: [MESSAGE]

1. Select the [KEY-DEVICE] or [COIN VENDOR].
2. Press the start key. The setting is set.
3. Turn the main power switch off and on.

Maintenance

item No.

Description

Display

Description

Setting range

Initial setting

CCD ADP
(NON P)

Without paper, single-sided original
(continuous operation)

CCD ADP

With paper, single-sided original

CCD RADP
(NON P)

Without paper, double-sided original
(continuous operation)

CCD RADP

With paper, double-sided original

SPEED

Switching between normal reading (600 dpi)
and high-speed reading

0 (Normal)/
1 (High-speed)

Display

Description

KEY-DEVICE

Sets the presence or absence of the key card or key counter

MESSAGE

Sets the message when optional equipment is not installed

Display

Description

KEY-CARD

The key card is installed

KEY-COUNTER

The key counter is installed

OFF

Not installed

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Search results

Summary of Contents for TASKALFA 300I

Reviews:

Related manuals for TASKALFA 300I

Brands by name

Popular brands

Kyocera TASKALFA 300I, Service Manual

Search results

Summary of Contents for TASKALFA 300I

Reviews:

Related manuals for TASKALFA 300I

Brands by name

Popular brands