manualshive.com logo in svg

Kyocera TASKALFA 300I, Service Manual

The Kyocera TASKALFA 300I is a multifunctional printer designed to enhance productivity in your workplace. Ensure seamless operation with our comprehensive User Manual, available for free download on our website. Explore advanced features, troubleshoot issues, and optimize your device's performance effortlessly with this user-friendly manual.

Share
Download
background image

2K5

CONTENTS

1-1 Specifications

1-1-1 Specifications..........................................................................................................................................1-1-1
1-1-2 Parts names............................................................................................................................................1-1-3

(1) Machine.............................................................................................................................................1-1-3
(2) Operation panel.................................................................................................................................1-1-6

1-1-3 Machine cross section ............................................................................................................................1-1-7

1-2 Installation

1-2-1  Installation environment .........................................................................................................................1-2-1
1-2-2 Unpacking and installation ......................................................................................................................1-2-2

(1) Installation procedure ........................................................................................................................1-2-2
(2) Setting initial copy modes................................................................................................................1-2-11

1-2-3 Installing the key counter (option) .........................................................................................................1-2-12

1-3 Maintenance Mode

1-3-1 Maintenance mode .................................................................................................................................1-3-1

(1) Executing a maintenance item ..........................................................................................................1-3-1
(2) Maintenance modes item list.............................................................................................................1-3-2
(3) Contents of the maintenance mode items.........................................................................................1-3-6

1-3-2 Management mode ...............................................................................................................................1-3-95

(1) Using the management mode .........................................................................................................1-3-95
(2) Common Settings............................................................................................................................1-3-96
(3) Copy Settings ..................................................................................................................................1-3-99
(4) Sending Settings .............................................................................................................................1-3-99
(5) Document Box Settings...................................................................................................................1-3-99
(6) Printer Settings..............................................................................................................................1-3-100
(7) Printing Reports/Sending Notice ...................................................................................................1-3-100
(8) Adjustment/Maintenance...............................................................................................................1-3-101
(9) Date/Timer.....................................................................................................................................1-3-101

(10) Editing Destination (Address Book/Adding One Touch Keys).......................................................1-3-102
(11) Internet Browser Setup..................................................................................................................1-3-103
(12) Applications ...................................................................................................................................1-3-104
(13) System Settings ............................................................................................................................1-3-104
(14) User Login Administration .............................................................................................................1-3-106
(15) Job accounting ..............................................................................................................................1-3-107

1-4 Troubleshooting

1-4-1 Paper misfeed detection .........................................................................................................................1-4-1

(1) Paper misfeed indication ...................................................................................................................1-4-1
(2) Paper misfeed detection conditions ..................................................................................................1-4-2
(3) Paper misfeeds .................................................................................................................................1-4-9

1-4-2 Self-diagnosis .......................................................................................................................................1-4-18

(1) Self-diagnostic function ...................................................................................................................1-4-18
(2) Self diagnostic codes ......................................................................................................................1-4-20

1-4-3 Image formation problems ....................................................................................................................1-4-34

(1) No image appears (entirely white)...................................................................................................1-4-35
(2) No image appears (entirely black)...................................................................................................1-4-35
(3) Image is too light. ............................................................................................................................1-4-36
(4) Background is visible.......................................................................................................................1-4-36
(5) A white line appears longitudinally. .................................................................................................1-4-36
(6) A black line appears longitudinally. .................................................................................................1-4-37
(7) A black line appears laterally...........................................................................................................1-4-37
(8) One side of the copy image is darker than the other.......................................................................1-4-37
(9) Black dots appear on the image......................................................................................................1-4-37

(10) Image is blurred...............................................................................................................................1-4-38
(11) The leading edge of the image is consistently misaligned with the original. ...................................1-4-38
(12) The leading edge of the image is sporadically misaligned with the original. ...................................1-4-38
(13) Paper creases. ................................................................................................................................1-4-38
(14) Offset occurs. ..................................................................................................................................1-4-39
(15) Image is partly missing....................................................................................................................1-4-39

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

NCR 7197 Manual preview
7197
Brand: NCR Pages: 10
EBS 2500 Installation And First Startup preview
2500
Brand: EBS Pages: 4
NCR 7156 Setup And User Manual preview
7156
Brand: NCR Pages: 38
Panasonic KX-PS8000 Reference Manual preview
KX-PS8000
Brand: Panasonic Pages: 155
Panasonic KX-MB2061 Operating Instructions Manual preview
KX-MB2061
Brand: Panasonic Pages: 160
BIXOLON SRP-500 Driver Installation Manual preview
SRP-500
Brand: BIXOLON Pages: 31
Ricoh Aficio 2238C Operating Instructions Manual preview
Aficio 2238C
Brand: Ricoh Pages: 126
Ultra electronics MAGICARD 300plus Quick Start Manual preview
MAGICARD 300plus
Brand: Ultra electronics Pages: 45
Lanier LD1110 Operating Instructions Manual preview
LD1110
Brand: Lanier Pages: 234
Oki MICROLINE 720 Handbook preview
MICROLINE 720
Brand: Oki Pages: 120
iDPRT iMOVE T3Pro User Manual preview
iMOVE T3Pro
Brand: iDPRT Pages: 74
Memjet AS-1180C Service Manual preview
AS-1180C
Brand: Memjet Pages: 181
GRAPHTEC SignJet JS310 Series Setup Manual preview
SignJet JS310 Series
Brand: GRAPHTEC Pages: 83
Tandy TRP-100 Operation Manual preview
TRP-100
Brand: Tandy Pages: 83
Thermo Scientific invitrogen EVOS FL Quick Reference preview
invitrogen EVOS FL
Brand: Thermo Scientific Pages: 6
Olivetti DR N17 Service Manual preview
DR N17
Brand: Olivetti Pages: 558
Aficio 2404WD Operating Instructions Manual preview
2404WD
Brand: Aficio Pages: 92
Epson Stylus CX1500 Notices And Warranty preview
Stylus CX1500
Brand: Epson Pages: 24

Brands by name

Popular brands

Load more brands