manualshive.com logo in svg

Kyocera TASKALFA 300I, Service Manual

The Kyocera TASKALFA 300I is a multifunctional printer designed to enhance productivity in your workplace. Ensure seamless operation with our comprehensive User Manual, available for free download on our website. Explore advanced features, troubleshoot issues, and optimize your device's performance effortlessly with this user-friendly manual.

Share
Download
background image

2K5

1-3-20

U030

Checking motor operation
Description

Drives each motor.

Purpose

To check the operation of each motor.

Method

1. Press the start key.
2. Select the motor to be operated.
3. Press the start key. The operation starts.

4. To stop operation, press the stop key.

Completion 

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U031

Checking switches for paper conveying
Description

Displays the on-off status of each paper detection switch on the paper path.

Purpose

To check if the switches for paper conveying operate correctly.

Method

1. Press the start key.
2. Turn each switch on and off manually to check the status.

When a switch is detected to be in the ON position, the display for that switch will be highlighted.

*: Optional.

Completion 

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Operation

MAIN

Main motor (MM) is turned ON

FEED

Paper feed motor (PFM) is turned ON

EJECT(FW)

Eject motor (EM) is turned on clockwise

EJECT(REV)

Eject motor (EM) is turned on counterclockwise

DRUM

Drum motor (DRM) is turned ON

Display

Switches

FEED1

Feed switch 1 (FSW1)

FEED2

Feed switch 2 (FSW2)

FEED3

Feed switch 3 (FSW3)

MP TRAY

MP feed switch (MPFSW)

REGIST

Registration switch (RSW)

EJECT

Eject switch (ESW)

BRANCH

Feedshift switch (FSSW)

DUPLEX

Duplex paper conveying switch (DUPPCSW)

JOB SEPARATOR

Job separator eject switch (JESW)*

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

WaxJet 6100 Service Reference Manual preview
6100
Brand: WaxJet Pages: 131
IBM 3160 Introduction And Planning Manual preview
3160
Brand: IBM Pages: 102
Fenix Imvico TK41 Operation Manual preview
TK41
Brand: Fenix Imvico Pages: 88
Oce im4511 Operation Manual preview
im4511
Brand: Oce Pages: 8
Canon imageRUNNER ADVANCE C5255 Instruction Manual preview
imageRUNNER ADVANCE C5255
Brand: Canon Pages: 64
Canon Powershot A3100 IS Supplementary Manual preview
Powershot A3100 IS
Brand: Canon Pages: 6
Canon imagePROGRAF TC-20 Installation Manual preview
imagePROGRAF TC-20
Brand: Canon Pages: 44
Canon C3226i Getting Started preview
C3226i
Brand: Canon Pages: 88
EBS Ink-Jet Systems Hi-Res EBS-2600 Manual preview
Hi-Res EBS-2600
Brand: EBS Ink-Jet Systems Pages: 3
Oki C7500n Maintenance Manual preview
C7500n
Brand: Oki Pages: 192
Oki LP470s Manual Rapide preview
LP470s
Brand: Oki Pages: 140
EFI Mimaki JV150 User Manual preview
Mimaki JV150
Brand: EFI Pages: 4
Ricoh SG 7100DN Installation Manual preview
SG 7100DN
Brand: Ricoh Pages: 17
idp SMART-70 User Manual preview
SMART-70
Brand: idp Pages: 48
Hitt Marking Devices POROUS Owner'S Manual preview
POROUS
Brand: Hitt Marking Devices Pages: 27
Lexmark MX71 series Service Manual preview
MX71 series
Brand: Lexmark Pages: 807
EBS EBS-6500 Basic Manual preview
EBS-6500
Brand: EBS Pages: 20
Star TSP100IIIBI Easy Setup Manual preview
TSP100IIIBI
Brand: Star Pages: 2

Brands by name

Popular brands

Load more brands