manualshive.com logo in svg

Kyocera TASKALFA 300I, Service Manual

The Kyocera TASKALFA 300I is a multifunctional printer designed to enhance productivity in your workplace. Ensure seamless operation with our comprehensive User Manual, available for free download on our website. Explore advanced features, troubleshoot issues, and optimize your device's performance effortlessly with this user-friendly manual.

Share
Download
background image

2K5

1-3-17

U003

Setting the service telephone number
Description

Sets the telephone number to be displayed when a service call code is detected.

Purpose

To set the telephone number to call service when installing the machine.

Method

Press the start key. The currently set telephone number is displayed. 

Setting

1. Press the start key.

The keys to enter the number are displayed on the touch panel.

2. Enter a telephone number (up to 15 digits).
3. Press the start key. The setting is set.

Completion 

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U004

Displaying the machine number
Description

Sets or displays the machine number.

Purpose

To check or set the machine number.

Method

1. Press the start key.

If the machine serial number of engine PWB matches with that of main PWB

If the machine serial number of engine PWB does not match with that of main PWB

Setting

Carry out if the machine serial number does not match.

1. Press [EXECUTE].
2. Press the start key. Writing of serial No. starts.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Operation

MACHINE No.

Displays the machine serial number

Display

Operation

MACHINE No. (MAIN)

Displays the machine serial number of main

MACHINE No. (ENGINE)

Displays the machine serial number of engine

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Oki Okipage8z Limited Warranty preview
Okipage8z
Brand: Oki Pages: 16
Olivetti PR2 plus Service Manual preview
PR2 plus
Brand: Olivetti Pages: 179
Olivetti JS-505 Service Manual preview
JS-505
Brand: Olivetti Pages: 36
Oki B6200 Series Maintenance Manual preview
B6200 Series
Brand: Oki Pages: 679
Oki PRO511DW Manual preview
PRO511DW
Brand: Oki Pages: 40
OKIDATA Pacemark 3410 Service Handbook preview
Pacemark 3410
Brand: OKIDATA Pages: 308
OKIDATA Pacemark 3410 Instruction Manual preview
Pacemark 3410
Brand: OKIDATA Pages: 9
OKIDATA MICROLINE 320 Quick Manual preview
MICROLINE 320
Brand: OKIDATA Pages: 2
Oki Microline 8480 FB Setup Manual preview
Microline 8480 FB
Brand: Oki Pages: 12
NEC Pinwriter P6 Specification preview
Pinwriter P6
Brand: NEC Pages: 10
Oce DFS10 Operator'S Manual preview
DFS10
Brand: Oce Pages: 90
Xante FilmMaker 4 Quick Reference Manual preview
FilmMaker 4
Brand: Xante Pages: 31
Star mC-Print3 MCP31LB How To Connect preview
mC-Print3 MCP31LB
Brand: Star Pages: 12
Muratec MFX-3550 User Manual preview
MFX-3550
Brand: Muratec Pages: 213
Olivetti PG 2028 SPECIAL Operation Manual preview
PG 2028 SPECIAL
Brand: Olivetti Pages: 104
Oki MPS730b Manual De L'Utilisateur preview
MPS730b
Brand: Oki Pages: 143
SEWOO SLK-TS100 User Manual preview
SLK-TS100
Brand: SEWOO Pages: 8
MHM Digital V Pro Operating Instructions Manual preview
Digital V Pro
Brand: MHM Pages: 52

Brands by name

Popular brands

Load more brands