manualshive.com logo in svg

Kyocera TASKALFA 300I, Service Manual

The Kyocera TASKALFA 300I is a multifunctional printer designed to enhance productivity in your workplace. Ensure seamless operation with our comprehensive User Manual, available for free download on our website. Explore advanced features, troubleshoot issues, and optimize your device's performance effortlessly with this user-friendly manual.

Share
Download
background image

2K5

1-3-21

U032

Checking clutch operation
Description

Turns each clutch on.

Purpose

To check the operation of each clutch.

Method

1. Press the start key.
2. Select the clutch to be operated.
3. Press the start key. The clutch turns on for 1 s.

4. To stop motor driving, press [MOTOR ON] again.

Completion 

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U033

Checking solenoid operation
Description

Applies current to each solenoid in order to check its ON status.

Purpose

To check the operation of each solenoid.

Method

1. Press the start key.
2. Select the solenoid to be operated.
3. Press the start key. The solenoid turns on for 1 s.

*Optional.

4. To stop motor driving, press [MOTOR ON] again.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Clutches

PF1

Paper feed clutch 1 (PFCL1)

PF2

Paper feed clutch 2 (PFCL2)

PF MP TRAY

MP paper feed clutch (MPPFCL)

FEED1

Feed clutch 1 (FCL1)

FEED2

Feed clutch 2 (FCL2)

LIFT MP TRAY

MP paper feed clutch (MPPFCL)

FEED MP TRAY

MP feed clutch (MPFCL)

REGIST

Registration clutch (RCL)

DUPLEX

Duplex feed clutch (DUPFCL)

MOTOR ON

The main motor (MM) and the paper feed motor (PFM) are turned on.

Display

Solenoids

BRANCH1 

Feedshift solenoid (FSSOL)

BRANCH2

Job feedshift solenoid (JFSSOL)*

MOTOR ON

The main motor (MM) and the paper feed motor (PFM) are turned on.

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Canon iR3245 Troubleshooting Manual preview
iR3245
Brand: Canon Pages: 300
Canon iR3245 Network Manual preview
iR3245
Brand: Canon Pages: 288
Canon iR3245 User Manual preview
iR3245
Brand: Canon Pages: 58
Canon iR1510 Quick Start Manual preview
iR1510
Brand: Canon Pages: 30
Oki OKIPAGE 8z Technical Features preview
OKIPAGE 8z
Brand: Oki Pages: 2
Oki OKIPAGE 8c Plus User Manual preview
OKIPAGE 8c Plus
Brand: Oki Pages: 48
Oki OKIPAGE 6e Maintenance Manual preview
OKIPAGE 6e
Brand: Oki Pages: 257
Oki OKIPAGE 14i Technical Reference preview
OKIPAGE 14i
Brand: Oki Pages: 113
Oki OKIPAGE 14e Setup Manual preview
OKIPAGE 14e
Brand: Oki Pages: 26
Oki OKIPAGE 14e Service Manual preview
OKIPAGE 14e
Brand: Oki Pages: 183
Oki MPS730b Material Safety Data Sheet preview
MPS730b
Brand: Oki Pages: 36
Oki MPS730b User Manual preview
MPS730b
Brand: Oki Pages: 136
Oki MPS710c Handy Reference preview
MPS710c
Brand: Oki Pages: 66
Oki MPS711c Manual De L'Utilisateur preview
MPS711c
Brand: Oki Pages: 123
Oki MPS711c User Manual preview
MPS711c
Brand: Oki Pages: 109
Oki Microline 520 User Manual preview
Microline 520
Brand: Oki Pages: 68
Oki Microline 3320 Maintenance Manual preview
Microline 3320
Brand: Oki Pages: 12
Oki OKIPOS X400 Manual De L'Utilisateur preview
OKIPOS X400
Brand: Oki Pages: 22

Brands by name

Popular brands

Load more brands