Kyocera TASKALFA 300I Service Manual Download Page 140 | Manualshive

Page: 140 / 408

background image

2K5

1-3-104

(12) Applications

Installing Applications

1. Insert the USB memory containing the application

to be installed into the USB memory slot (A1).

2. Press [Add].
3. Select the application to be installed and press

[Install].
You can view detailed information on the selected
application by pressing [Detail].

4. When the confirmation screen appears, press

[Yes].
Installation of the application begins. Depending on
the application being installed, the installation may
take some time. Once the installation ends, the
original screen reappears.

5. To install another application, repeat steps 3 to 4.
6. To remove the USB memory, press [Remove Mem-

ory] and wait until the Removable Memory can be
safely removed message appears. Then remove
the USB memory.

Activating/Deactivating Application

1. Select the desired application and press [Activate].

You can view detailed information on the selected
application by pressing [Detail].

2. Enter the license key and press [Official]. Some

applications do not require you to enter an license
key. If the license key entry screen does not
appear, go to Step 3.
To use the application as a trial, press [Trial] without
entering the license key.

3. When the confirmation screen appears, press

[Yes].

Deleting Applications

1. Select the application to be deleted and press

[Delete].
You can view detailed information on the selected
application by pressing [Detail].

2. When the deletion confirmation screen appears,

press [Yes]. The application is deleted.

(13) System Settings

Restarting the System

1. Press [Execute] of Restart.
2. When the confirmation screen appears, press

[Yes]. The system is restarted.

Network Setup

TCP/IP (IPv4) Setup

1. Press [Next] of Network and then [Next] of TCP/IP

Setting.

2. Press [Change] of TCP/IP.
3. Press [On] and then press [OK].
4. Press [Change] of IPv4.
5. Press [DHCP].
6. Press [Off] of DHCP and then press [OK].
7. Press [Bonjour].
8. Press [Off] of Bonjour and then press [OK].
9. Press [IP Address] and enter the address using the

numeric keys.

10. Press [Subnet Mask] and enter the address using

the numeric keys.

11. Press [Default Gateway] and enter the address

using the numeric keys.

12. Check if all the address entries are correct and

press [OK].

13. After changing the setting, restart the system or

turn the machine OFF and then ON again.

TCP/IP (IPv6) Setup

1. Press [Next] of Network and then [Next] of TCP/IP

Setting.

2. Press [Change] of TCP/IP.
3. Press [On] and then press [OK].
4. Press [Next] of IPv6.
5. Press [Change] of IPv6.
6. Press [On].
7. Press [OK].
8. After changing the setting, restart the system or

turn the machine OFF and then ON again.

Manual Setting (IPv6)

1. Press [Next] of Network and then [Next] of TCP/IP

Setting.

2. Press [Next] of IPv6.
3. Press [Next] of Manual Setting.
4. Press [IP Address (Manual)] to enter IP address.
5. Press [OK].

Press [# Keys] of Prefix Length (0 - 128) to enter
the prefix length using the numeric keys.

6. Press [Default Gateway] to enter the default gate-

way.

7. Check that all the entries are correct and Press

[OK].

8. After changing the setting, restart the system or

turn the machine OFF and then ON again.

«
...
138
139
140
141
142
...
»

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Brand: Oki Pages: 282

Brand: TallyGenicom Pages: 3

Brand: Xerox Pages: 9

Brand: Xerox Pages: 2

Brand: Xerox Pages: 8

Brand: Xerox Pages: 4

Brand: Xerox Pages: 150

Brand: Xerox Pages: 4

Brand: Xerox Pages: 6

Brand: Xerox Pages: 2

DocuPrint N2125

Brand: Xerox Pages: 246

DocuPrint N2025

Brand: Xerox Pages: 378

DocuPrint N2025

Brand: Xerox Pages: 176

DocuPrint C3290 FS

Brand: Xerox Pages: 240

Brand: Xerox Pages: 5

Brand: Xerox Pages: 7

Brand: Xerox Pages: 2

Brand: Xerox Pages: 47

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands