Kyocera TASKALFA 300I Service Manual Download Page 173

Page: 173 / 408

2K5

1-4-29

C7910

Developing unit EEPROM error

Reading from or writing to EEPROM
cannot be performed.

Poor contact in the
connector termi-
nals.

Check the connection of connector on the
engine PWB and the continuity across the
connector terminals. Repair or replace if
necessary.

Defective develop-
ing unit.

Replace the developing unit.

C8030

Tray upper limit detection problem
(optional document finisher)

When the tray elevation motor raises a
tray, the ON status of the tray upper limit
sensor is detected.

The tray upper limit
sensor, paper sur-
face sensor 1/2
connector makes
poor contact.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
remedy or replace the cable.

Defective tray
upper limit sensor,
paper surface sen-
sor 1/2.

Replace the sensor.

Defective finisher
main PWB.

Replace the finisher main PWB and check
for correct operation.

C8040

Belt problem (optional document fin-
isher)

The belt sensor does not turn on/off
within specified time of the belt solenoid
turning on.

The belt sensor,
belt solenoid con-
nector makes poor
contact.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
remedy or replace the cable.

Defective belt sen-
sor.

Replace the belt sensor.

Defective belt sole-
noid.

Replace the belt solenoid.

Defective finisher
main PWB.

Replace the finisher main PWB and check
for correct operation.

C8140

Tray elevation motor problem
(optional document finisher)

The tray low limit sensor or paper sur-
face sensor 1/2 cannot be detected to be
on within 10 s since the tray elevation
motor is activated.

The tray elevation
motor connector
makes poor con-
tact.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
remedy or replace the cable.

The tray elevation
motor malfunc-
tions.

Replace the tray elevation motor.

The tray lower limit
sensor, paper sur-
face sensor 1/2
connector makes
poor contact.

Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
remedy or replace the cable.

Defective tray
lower limit sensor,
paper surface sen-
sor 1/2.

Replace the sensor.

Defective finisher
main PWB.

Replace the finisher main PWB and check
for correct operation.

Code

Contents

Remarks

Causes

Check procedures/corrective measures

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Search results

Summary of Contents for TASKALFA 300I

Reviews:

Related manuals for TASKALFA 300I

Brands by name

Popular brands

Kyocera TASKALFA 300I, Service Manual

Search results

Summary of Contents for TASKALFA 300I

Reviews:

Related manuals for TASKALFA 300I

Brands by name

Popular brands