Kyocera TASKALFA 300I Service Manual Download Page 194 | Manualshive

Page: 194 / 408

background image

2K5

1-4-50

(3) Scan to E-mail error codes

Code

Display

Remarks

Causes

Check procedures/corrective measures

1101

Error: Host name

SMTP sever name is not set.
Error SMTP server name.

Register [SMTP Server Name] in
[Advanced]-[SMTP] -[General] in
COMMAND CENTER.

1102

Error: User/Password

User ID for the authentication
is not entered or entered
wrongly.
Wrong authentication pass-
word is entered.

Enter the correct user ID/password for
authentication at [Advance] in COMMAND
CENTER.
Enter the password of [Login User Name] of
the [POP3] page or the [SMTP] page cor-
rectly.

1104

Error: No Recipient address

The destination address is not
specified.

Specify the destination address.

1105

Error: Not support protocol

SMTP Protocol is set to OFF.

Check ON [SMTP] in [Advanced]-[SMTP] -
[General] in COMMAND CENTER.

1106

Error: No Sender Info

Sender address is not enter

Enter the correct [Sender Address] in
[Advanced]-[SMTP] -[General] in
COMMAND CENTER.

2101

Error: Can not connect

Select [Other authenticate]
when authenticating POP
before SMTP.

Select valid POP3 user other than [Other].

The specified server is not
SMTP server.

Enter the correct [SMTP Server Name] in
[Advanced]-[SMTP] -[General] in
COMMAND CENTER.

Network is not connected.

Check if the server is operating properly.
Check the network connection (cable. net-
work condition within LAN, etc.).

2102

Error: Can not connect with
timeout

The server is unable to com-
municate.

Check if the server is operating properly.

2103

Error: Response wait with
timeout

The server is unable to com-
municate.

Check if the server is operating properly.

2201

Error: Network transfer

Error occurs on the network.

Check the network connection (cable. net-
work condition within LAN, etc.).

2202

Error: Network transfer with
timeout

Error occurs on the network.

Check the network connection (cable. net-
work condition within LAN, etc.).

2203

Error: Response wait with
timeout

Response is not returned
from the server above speci-
fied time.

Check the network connection (cable. net-
work condition within LAN, etc.).

2204

Error: E-Mail Size limit

The size of E-mail exceeds its
limit.

Change the [E-mail Size Limit] in
[Advanced]-[SMTP] -[General]-[E-mail Set-
ting] in COMMAND CENTER.

3101

Error: Server response

The server is error status.

Check if the server is working properly.

Server setting is not authenti-
cated normally.

Check the settings for client/server authenti-
cation.

3201

Error: Not Found Authenti-
cation Mechanism

Unsupported SMTP Authenti-
cation Mechanism is found.

Check the settings for client/server Authenti-
cation Mechanism.

9181

Error: Page max count over

The number of pages of a
send file exceeded 999
pages.

Set the number of pages as 999 or less.

«
...
192
193
194
195
196
...
»

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Brand: YOUPAI Pages: 15

Brand: TallyGenicom Pages: 15

Brand: F+D Feinwerk- und Drucktechnik Pages: 22

Brand: JCM Pages: 22

Brand: Oki Pages: 197

Brand: BCS Pages: 151

Brand: Evolis Pages: 63

Brand: Lexmark Pages: 8

Brand: Savin Pages: 4

Brand: Epson Stylus Pages: 4

WorkCentre 6655i

Brand: Xerox Pages: 282

Brand: Canon Pages: 48

Pixma PRO-100S series

Brand: Canon Pages: 4

Pixma PRO-100S series

Brand: Canon Pages: 2

Brand: Canon Pages: 570

Brand: Canon Pages: 571

Brand: Canon Pages: 4

imageRUNNER ADVANCE DX C5870i

Brand: Canon Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands