Kyocera TASKALFA 300I Service Manual Download | Manualshive

Page: 151 / 408

background image

2K5-1

1-4-7

Optional
finisher

80
Finisher timeout jam
(built-in finisher)

(Document finisher)
Paper ejection is not output from the machine to the doc-
ument finisher within specified time of the paper entry
sensor (PES) turning on.

15 s

(Built-in finisher)
Paper ejection is not output from the machine to the doc-
ument finisher within specified time of the paper convey-
ing switch (PCSW) turning on.

15 s

81
Paper entry sensor
nonarrival jam

(Document finisher)
The paper entry sensor (PES) is not turned on even if a
specified time has elapsed after the machine eject signal
was received.

1201 ms

(Built-in finisher)
The paper conveying switch (PCSW) is not turned on
even if a specified time has elapsed after the machine
eject signal was received.

2000 ms

(Built-in finisher)
The paper conveying switch (PCSW) does not turn off
within specified time of its turning on when paper is con-
veyed to the process table from the paper conveying unit.

1429 ms + Paper
length

82
Jam in stapler

(Document finisher)
The staple home position sensor (STSPS) is not turned
on within the specified time when driving the staple motor
(STM).

-

(Built-in finisher)
The staple home position sensor (STHPS) is not turned
on within the specified time when driving the staple motor
(STM).

600 ms

83
Exit sensor stay jam

(Document finisher)
In the straight mode, the exit sensor (EPS) is not turned
off within specified time of its turning on.

-

(Document finisher)
In the bundle discharge mode or the staple mode, bundle
discharge operation does not turn off within specified time
since the operation starts.

902 ms

(Built-in finisher)
The paper conveying switch (PCSW) does not turn off
within specified time of its turning on when paper is
ejected to the finisher tray from the process table.

1429 ms + Paper
length

91
Finisher cover open
(document finisher)

The finisher cover becomes open during paper is run-
ning.
Paper is remaining in paths at power on.

-

92
Eject paper sensor
non-arrival jam (docu-
ment finisher)

In the straight mode, the eject paper sensor (EPS) is not
turned on even if a specified time has elapsed after the
paper entry sensor (PES) was turned on.

-

Section

Description

Conditions

Specified time

«
...
149
150
151
152
153
...
»

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Brand: Unimark Pages: 38

BOOKLET MAKER BK5010

Brand: Ricoh Pages: 74

WorkCentre 7328

Brand: Xerox Pages: 8

Brand: StarTech.com Pages: 13

Brand: Oki Pages: 8

Brand: Xerox Pages: 78

Perfecta 2400STP

Brand: Variquest Pages: 12

Brand: Oki Pages: 204

Brand: Shandong New Beiyang Information Technology Co. Pages: 47

1235/DX - Phaser Color Laser Printer

Brand: Xerox Pages: 144

E-Class Mark III

Brand: datamax-o'neli Pages: 58

A920 - Personal All-in-One Printer Color Inkjet

Brand: Dell Pages: 83

Brand: Dell Pages: 5

Brand: Dell Pages: 4

1815 Mono Laser

Brand: Dell Pages: 152

1815dn Multifunction Mono Laser Printer

Brand: Dell Pages: 148

Brand: Dell Pages: 150

2355 Mono Laser

Brand: Dell Pages: 181

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands