manualshive.com logo in svg

Kyocera TASKALFA 300I, Service Manual

The Kyocera TASKALFA 300I is a multifunctional printer designed to enhance productivity in your workplace. Ensure seamless operation with our comprehensive User Manual, available for free download on our website. Explore advanced features, troubleshoot issues, and optimize your device's performance effortlessly with this user-friendly manual.

Share
Download
background image

2K5

1-3-100

(6) Printer Settings

Emulation

1. Press [Change] of Emulation.
2. Select the desired emulation.
3. Press [OK].

Setting of Alternative Emulation

1. Press [Change] of Emulation, [KPDL(Auto)] and 

then [Alt Emulation].

2. Select the desired alternative emulation and then 

press [OK].

3. Press [OK].

Setting of KPDL error report

1. Press [Change] of Emulation, [KPDL] or 

[KPDL(Auto)] and then [KPDL Error Report].

2. Press [On] or [Off] and then press [OK].
3. Press [OK].

EcoPrint

1. Press [Change] of EcoPrint.
2. Press [Off] or [On].
3. Press [OK].

Override A4/Letter

1. Press [Change] of Override A4/Letter.
2. Press [Off] or [On].
3. Press [OK].

Duplex

1. Press [Change] of Duplex.
2. Press [1-sided], [2-sided Bind LongEdge], or [2-

sided Bind ShortEdge].

3. Press [OK].

Copies

1. Press [Change] of Copies.
2. Press [+],[-] or the numeric keys to set the default 

number of copies.

3. Press [OK].

Orientation

1. Press [Change] of Orientation.
2. Press [Portrait] or [Landscape].
3. Press [OK].

Form Feed Timeout

1. Press cursor down key and [Change] of Form Feed 

Timeout.

2. Press [+] or [-] to set the Form Feed Timeout.

You can set the timeout delay in seconds.
You cannot use the number keypad to enter this 
value.

3. Press [OK].

LF Action

1. Press cursor down key and [Change] of LF Action.
2. Press [LF Only], [LF and CR] or [Ignore LF].
3. Press [OK].

CR Action

1. Press cursor down key and [Change] of CR Action.
2. Press [CR Only], [LF and CR] or [Ignore CR].
3. Press [OK].

Paper Feed Mode

1. Press cursor down key and [Change] of Paper 

Feed Mode.

2. Press [Auto] or [Fixed].
3. Press [OK].

(7) Printing Reports/Sending Notice

Printing Reports

1. Press [Next] of Print Report.
2. Press [Print] for the report you want to print. Print-

ing starts.
A confirmation screen appears. Press [Yes].

Send Result Report

1. Press [Next] of Result Report Setting, [Next] of 

Send Result Report and then [Change] of E-mail/
Folder.

2. Press [Off], [On], or [Error Only].
3. Press [OK].

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Canon Color imageCLASS MF8580Cdw Getting Started Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 36
Canon Color imageCLASS MF8580Cdw Settings Manual preview
Color imageCLASS MF8580Cdw
Brand: Canon Pages: 20
Canon Color imageCLASS MF8280Cw Settings Manual preview
Color imageCLASS MF8280Cw
Brand: Canon Pages: 24
Canon Color imageCLASS MF8080Cw Starter Manual preview
Color imageCLASS MF8080Cw
Brand: Canon Pages: 39
Canon Color imageCLASS MF8050Cn Starter Manual preview
Color imageCLASS MF8050Cn
Brand: Canon Pages: 32
Canon Color imageCLASS LBP7660Cdn Quick Setup Manual preview
Color imageCLASS LBP7660Cdn
Brand: Canon Pages: 2
Canon Color imageCLASS 8180c Quick Start Manual preview
Color imageCLASS 8180c
Brand: Canon Pages: 24
Canon CD-300 Printer Manual preview
CD-300
Brand: Canon Pages: 30
Canon C3000 - MultiPASS Color Inkjet Printer Parts Catalog preview
C3000 - MultiPASS Color Inkjet Printer
Brand: Canon Pages: 41
Canon Color imageCLASS MF8170c Specification preview
Color imageCLASS MF8170c
Brand: Canon Pages: 2
Canon Color imageCLASS MF8170c Facsimile Manual preview
Color imageCLASS MF8170c
Brand: Canon Pages: 98
Canon Color imageCLASS MF8170c Instructions Manual preview
Color imageCLASS MF8170c
Brand: Canon Pages: 8
Canon Color imageCLASS MF8080Cw Configuration Manual preview
Color imageCLASS MF8080Cw
Brand: Canon Pages: 46
Canon Color imageRUNNER LBP5360 Release Note preview
Color imageRUNNER LBP5360
Brand: Canon Pages: 3
Canon imageCLASS Mf6160dw Getting Started Manual preview
imageCLASS Mf6160dw
Brand: Canon Pages: 64
Canon imageCLASS MF6500 Series Advanced Manual preview
imageCLASS MF6500 Series
Brand: Canon Pages: 132
Canon imageCLASS MF5550 Software Manual preview
imageCLASS MF5550
Brand: Canon Pages: 120
Canon imageCLASS MF5630 User Manual preview
imageCLASS MF5630
Brand: Canon Pages: 85

Brands by name

Popular brands

Load more brands