Kyocera TASKALFA 300I Service Manual Download Page 152

Page: 152 / 408

2K5-1

1-4-8

Optional
finisher

93
Reverse sensor jam
(document finisher)

The reverse sensor (SBS) does not turn on within speci-
fied time of paper entry sensor (PES) turning on (unfin-
ished reversing canceled).

719 ms

The reverse sensor (SBS) is not turned on within speci-
fied time (unfinished reversing set).

431 ms

The reverse sensor (SBS) is not turned off within speci-
fied time its turning on (resident reversing canceled).

3000 ms

The reverse sensor (SBS) is not turned off within speci-
fied time its turning on (resident reversing set).

700 ms

94
Paper entry sensor
stay/remaining jam
(document finisher)

The paper entry sensor (PES) is not turned off within
specified time its turning on.

2250 ms

95
Paper conveying sen-
sor jam (document fin-
isher)

The paper conveying sensor (PCS) is not turned off
within specified time its turning on (reversing canceled).

2250 ms

The paper conveying sensor (PCS) is not turned off
within specified time its turning on (reversing set).

656 ms

96
Jam between the built-
in finisher and machine
(built-in finisher)

The paper conveying switch (PCSW) is not turned on
within the specified time when paper is ejected to the fin-
isher tray from the process table.

2000 ms

Section

Description

Conditions

Specified time

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Search results

Summary of Contents for TASKALFA 300I

Reviews:

Related manuals for TASKALFA 300I

Brands by name

Popular brands

Kyocera TASKALFA 300I, Service Manual

Search results

Summary of Contents for TASKALFA 300I

Reviews:

Related manuals for TASKALFA 300I

Brands by name

Popular brands