Kyocera TASKALFA 300I Service Manual Download Page 32 | Manualshive

Page: 32 / 408

background image

2K5

1-2-10

1. Connect the power cord to the connector on the machine.
2. Insert the power plug into the wall outlet.

1. Turn the main power switch on. Toner installation is started.
2. The drive chain is disengaged when toner installation is completed.

Run maintenance mode U130 if [Add Toner] remains displayed even after the drive chain is disengaged.

1. Press the status/job cancel key. Enter the maintenance mode by entering 10871087 using the numeric keys.
2. Enter 278 using the numeric keys and press the start key.
3. Select [TODAY] and press the start key. The delivery date is set.
4. Press the stop key.

1. Enter 000 using the numeric keys and press the start key.
2. Select MAINTENANCE and press the start key to output a list of the current settings of the maintenance items.
3. Press the stop key.

1. Enter 001 using the numeric keys and press the start key. The machine exits the maintenance mode.

1. Select [Report Print] to output the user various setting reports.

1. Place an original and make test copies.

1. According to need, attach the correspond language label.

Connect the power cord.

Installing toner.

Setting the delivery date (maintenance item U278).

Output an own-status report (maintenance item U000).

Exit maintenance mode.

Print out the user setting list.

Make test copies.

Attaching the language label (230 V specifications only).

Completion of the machine installation.

«
...
30
31
32
33
34
...
»

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

Brand: BadgePass Pages: 2

Brand: LabelTac Pages: 15

Brand: Pantum Pages: 164

Brand: Canon Pages: 34

Brand: Canon Pages: 369

Brand: Ricoh Pages: 682

Brand: A&D Pages: 31

Brand: Oki Pages: 276

Brand: Brightek Pages: 8

Brand: Lexmark Pages: 79

Brand: Oki Pages: 271

WorkCentre Pro 421

Brand: Xerox Pages: 162

Brand: Pantum Pages: 155

Brand: Rimage Pages: 217

Brand: Source Technologies Pages: 47

Brand: Copystar Pages: 4

E-Class Mark III

Brand: datamax-o'neli Pages: 58

Brand: Citizen Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands