manualshive.com logo in svg

Kyocera TASKALFA 300I, Service Manual

The Kyocera TASKALFA 300I is a multifunctional printer designed to enhance productivity in your workplace. Ensure seamless operation with our comprehensive User Manual, available for free download on our website. Explore advanced features, troubleshoot issues, and optimize your device's performance effortlessly with this user-friendly manual.

Share
Download
background image

2K5

1-3-38

U074

Adjusting the DP input light luminosity
Description

Sets the luminosity correction for scanning originals from the DP.

Purpose

Modify the setting only if a spotted background appears when a bluish original is scanned from the DP.

Setting

1. Press the start key.
2. Change the setting using the +/- or numeric keys.

Settings 0: No correction / 1: Slight correction / 2: Medium correction / 3: Strong correction

3. Press the start key. The value is set.

Supplement

While this maintenance item is being executed, copying from an original is available in interrupt copying mode 
(which is activated by pressing the system menu key).

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U080

Setting the economy mode
Description

Sets the level in the economy mode.

Purpose

To increase or decrease the image density in the eco-print mode.

Setting

1. Press the start key. 
2. Change the setting value using the +/- or numeric keys.

Increasing the setting makes the image darker; decreasing it makes the image lighter.

3. Press the start key. The value is set.

Supplement

While this maintenance item is being executed, copying from an original is available in interrupt copying mode 
(which is activated by pressing the system menu key).

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

Setting range

Initial setting

INPUT DATA

DP input light luminosity correction

0 to 3

0

Display

Description

Setting range

Initial setting

ECO MODE

Exposure is toner economy mode

0 to 100

60

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

QMS 1060 User Manual preview
1060
Brand: QMS Pages: 311
Tally T6090 Maintenace Manual preview
T6090
Brand: Tally Pages: 202
Xerox PHASER 6250 Reference Manual preview
PHASER 6250
Brand: Xerox Pages: 9
Xerox PHASER 6250 Management Manual preview
PHASER 6250
Brand: Xerox Pages: 2
Xerox PHASER 6250 Setting Instructions Manual preview
PHASER 6250
Brand: Xerox Pages: 8
Xerox Phaser 6200 Function Manual preview
Phaser 6200
Brand: Xerox Pages: 4
Xerox Phaser 4622 User Manual preview
Phaser 4622
Brand: Xerox Pages: 150
Xerox Phaser 4600 Supplementary Manual preview
Phaser 4600
Brand: Xerox Pages: 4
Xerox Phaser 4 400 Driver Installation Instruction preview
Phaser 4 400
Brand: Xerox Pages: 6
Xerox VersaLink C400 Installation Manual preview
VersaLink C400
Brand: Xerox Pages: 2
Xerox DocuPrint N2125 System Administrator Manual preview
DocuPrint N2125
Brand: Xerox Pages: 246
Xerox DocuPrint N2025 Service Manual preview
DocuPrint N2025
Brand: Xerox Pages: 378
Xerox DocuPrint N2025 User Manual preview
DocuPrint N2025
Brand: Xerox Pages: 176
Xerox DocuPrint C3290 FS User Manual preview
DocuPrint C3290 FS
Brand: Xerox Pages: 240
Xerox Phaser 6120N Guia De Utilização Rápida preview
Phaser 6120N
Brand: Xerox Pages: 5
Xerox Phaser 6100 Quick Reference Manual preview
Phaser 6100
Brand: Xerox Pages: 7
Xerox Phaser 6100 Setup Manual preview
Phaser 6100
Brand: Xerox Pages: 2
Xerox Phaser 8200 Networking Setup Manual preview
Phaser 8200
Brand: Xerox Pages: 47

Brands by name

Popular brands

Load more brands