manualshive.com logo in svg

Kyocera TASKALFA 300I, Service Manual

The Kyocera TASKALFA 300I is a multifunctional printer designed to enhance productivity in your workplace. Ensure seamless operation with our comprehensive User Manual, available for free download on our website. Explore advanced features, troubleshoot issues, and optimize your device's performance effortlessly with this user-friendly manual.

Share
Download
background image

2K5

1-3-68

U339

Setting the drum heater ON/OFF
Description

Turns the drum heater on or off during sleep mode.

Purpose

Set according to the preference of the user.

Setting

1. Press the start key.
2. Change the setting using the +/- or numeric keys.

*: The drum heater is off at sleep mode when the value is 0.
   The drum heater is on at sleep mode when the value is between 1 and 4.

3. Press the start key. The setting is set.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

U341

Specific paper feed location setting for printing function
Description

Sets a paper feed location specified for printer output.

Purpose

To use a paper feed location only for printer output.
A paper feed location specified for printer output cannot be used for copy output.

Method

1. Press the start key.
2. Select the paper feed location for the printer.

Two or more cassette can be selected.

When an optional paper feed device is not installed, the corresponding count is not displayed.

3. Press the start key. The setting is set.

Completion

Press the stop key. The screen for selecting a maintenance item No. is displayed.

Maintenance

item No.

Description

Display

Description

Setting range

Initial setting

MODE

Setting the drum heater ON/OFF

0 to 4*

0

Display

Description

CASSETTE 1

Cassette 1

CASSETTE 2

Cassette 2

CASSETTE 3

Cassette 3 (optional paper feeder)

CASSETTE 4

Cassette 4 (optional paper feeder)

Summary of Contents for TASKALFA 300I

























































































































































































































































































































































































































Reviews:

No comments

Related manuals for TASKALFA 300I

CAB A Series Programming Manual preview
A Series
Brand: CAB Pages: 263
IBM RS/6000 44P Series 270 User Manual preview
RS/6000 44P Series 270
Brand: IBM Pages: 216
TallyGenicom LGe06 Datasheet preview
LGe06
Brand: TallyGenicom Pages: 2
Oki B4600 Series Specifications preview
B4600 Series
Brand: Oki Pages: 2
Tally T8024 User Manual preview
T8024
Brand: Tally Pages: 266
Radio Shack Line Printer VIII Hardware Manual preview
Line Printer VIII
Brand: Radio Shack Pages: 54
Kyocera C5020N - FS Color LED Printer Command Reference Manual preview
C5020N - FS Color LED Printer
Brand: Kyocera Pages: 410
Printekmobile MLP-35 Quick Start Manual preview
MLP-35
Brand: Printekmobile Pages: 2
Xerox 490ST - Document Centre B/W Laser Printer System Administration Manual preview
490ST - Document Centre B/W Laser Printer
Brand: Xerox Pages: 322
SPRT SP-POS5810 User Manual preview
SP-POS5810
Brand: SPRT Pages: 12
Xerox 6250N - Phaser Color Laser Printer Service Manual preview
6250N - Phaser Color Laser Printer
Brand: Xerox Pages: 467
Canon LBP7018C E-Manual preview
LBP7018C
Brand: Canon Pages: 343
Canon LBP654C Series Getting Started preview
LBP654C Series
Brand: Canon Pages: 380
Canon MAXIFY GX4070 Manual preview
MAXIFY GX4070
Brand: Canon Pages: 13
datamax-o'neli E-Class Mark III Operator'S Manual preview
E-Class Mark III
Brand: datamax-o'neli Pages: 58
Citizen PPU-231 User Manual preview
PPU-231
Brand: Citizen Pages: 75
InfoSight LabeLase LL2800 Basic Operations & Maintenance Manual preview
LabeLase LL2800
Brand: InfoSight Pages: 24
Toshiba TRST-A10 SERIES Quick Installation Manual preview
TRST-A10 SERIES
Brand: Toshiba Pages: 6

Brands by name

Popular brands

Load more brands