Juniper JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010 Command Reference Manual Download Page 811

Page: 811 / 1502

ip dhcp-local cable-modem

Syntax

[ no ] ip dhcp-local cable-modem dhcp-server

ipAddress

Release Information

Command introduced before JunosE Release 7.1.0.

Description

Specifies the IP address of the external DHCP server to which the DHCP local server will
relay DHCP messages from cable modems. The

version removes the cable modem

configuration.

NOTE:

This command is deprecated and might be removed completely in a future

release. Use the

set dhcp vendor-option

command to configure the vendor class

identifier option to match the string used by cable modems to replace the function of
this command.

Options

•

ipAddress

—IP address of the cable modem DHCP server

Mode

Global Configuration

767

Chapter 10: I Commands

Summary of Contents for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Reviews:

Related manuals for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Brands by name

Popular brands

Juniper JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010, Command Reference Manual

Search results

Summary of Contents for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Reviews:

Related manuals for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Brands by name

Popular brands