Juniper JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010 Command Reference Manual Download Page 961

Page: 961 / 1502

ip rip authentication key

Syntax

ip rip authentication key [ 0 | 8 ]

authkey

no ip rip authentication key

Release Information

Command introduced before JunosE Release 7.1.0.

Description

Specifies the password for text authentication and the key for MD5 authentication. The

version clears the key for the interface. Supported only in RIP version 2. Authentication

is disabled by default.

Options

0—Indicates the

authKey

is entered in unencrypted form (plaintext); this is the default

option

•

8—Indicates the

authKey

is entered in encrypted form (ciphertext)

•

authkey

—Password sent with RIP messages or the key used to encrypt/decrypt RIP

messages, depending on the authentication mode set for this interface

Mode

Interface Configuration, Subinterface Configuration

917

Chapter 10: I Commands

Summary of Contents for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Reviews:

Related manuals for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Brands by name

Popular brands

Juniper JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010, Command Reference Manual

Search results

Summary of Contents for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Reviews:

Related manuals for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Brands by name

Popular brands