Juniper JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010 Command Reference Manual Download Page 673

Page: 673 / 1502

forward

Syntax

[ no ] [ suspend ] forward
[ interface

interfaceType interfaceSpecifier

[ next-hop

nextHop

[ ignore-default-route ] ]
[ order

orderValue

] ] | [ next-hop

nextHop

[ virtual-router

vrName

]

[ ignore-default-route ] [ order

orderValue

] ] |

[ order

orderValue

] | classifier-group

claclName

] [ precedence

precValue

]

Release Information

Command introduced before JunosE Release 7.1.0.

Description

Defines a rule to forward all packets that match the specified classifier control list. If you
do not specify a classifier control list using the

classifier-group

keyword, the router will

select all packets from the interface in the direction of the attached policy list. The

version removes the rule from the policy list; the

suspend

version temporarily suspends

the forward rule; the

no suspend

version resumes application of a suspended rule.

See the forward interface and forward next-hop commands for descriptions of the
Classifier Group Configuration mode versions of this command.

Options

•

interfaceType

—Interface type; see “Interface Types and Specifiers” on page 5 (IP

policy lists only)

•

interfaceSpecifier

—Particular interface; format varies according to interface type; see

“Interface Types and Specifiers” on page 5 (IP policy lists only)

•

nextHop

—Next-hop IP address (IP policy lists only)

•

ignore-default-route—Ignores the default route as a consideration for the next hop (IP
policy lists only)

•

vrName

—Name of the virtual router (IP policy lists only)

•

orderValue

—Order of this forward rule within the single classifier; in the range 1–32767;

default value is 100 (IP policy lists only)

•

claclName

—Classifier control list used to classify packets for this policy

•

precValue

—Precedence of this rule in relation to other rules within this set: in the range

0–32768; default value is 100

Mode

Policy List Configuration

Summary of Contents for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010






























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Reviews:

Related manuals for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Brands by name

Popular brands

Juniper JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010, Command Reference Manual

Search results

Summary of Contents for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Reviews:

Related manuals for JUNOS OS 10.3 - XML MANAGEMENT PROTOCOL GUIDE 6-30-2010

Brands by name

Popular brands