manualshive.com logo in svg

Jatco RE4F04B, Manual

Share
Download
Jatco RE4F04B Manual Download Page 194

AT-194

[RE4F04B]

DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM 

POWER SOURCE)

Revision: November 2006

2006 Altima

DTC BATT/FLUID TEMP SEN (A/T FLUID TEMP SENSOR CIRCUIT AND TCM
POWER SOURCE)

PFP:31940

Description

ECS00996

The A/T fluid temperature sensor detects the A/T fluid temperature
and sends a signal to the TCM.

CONSULT-II REFERENCE VALUE IN DATA MONITOR MODE

Remarks: Specification data are reference values.

On Board Diagnosis Logic

ECS00997

Diagnostic trouble code BATT/FLUID TEMP SEN with CONSULT-II or 8th judgement flicker without CON-
SULT-II is detected when TCM receives an excessively low or high voltage from the sensor.

Possible Cause

ECS00998

Check the following items.

●

Harness or connectors
(The sensor circuit is open or shorted.)

●

A/T fluid temperature sensor

Diagnostic Trouble Code (DTC) Confirmation Procedure

ECS00999

After the repair, perform the following procedure to confirm the malfunction is eliminated.

WITH CONSULT-II

1.

Start engine.

SAT283HB

SAT021J

Monitor item

Condition

Specification (Approximately)

A/T fluid temperature sensor

Cold [20

°

C (68

°

F)]

↓

Hot [80

°

C (176

°

F)]

1.5V

↓

0.5V

2.5 k

Ω

↓

0.3 k

Ω

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands