manualshive.com logo in svg

Jatco RE4F04B, Manual

The Jatco RE4F04B is a reliable and durable automatic transmission system commonly used in various vehicles. Ensure proper maintenance of your transmission system by downloading the free user manual from manualshive.com to ensure optimal performance and longevity. Keep your vehicle running smoothly with a comprehensive manual at your disposal.

Share
Download
background image

AT-86

[RE4F04B]

TROUBLE DIAGNOSIS - BASIC INSPECTION

Revision: November 2006

2006 Altima

Cruise Test — Part 1

1. 

CHECK STARTING GEAR (D

1

 ) POSITION

1.

Drive vehicle for approximately 10 minutes to warm engine oil and ATF up to operating temperature.

2.

Park vehicle on flat surface.

3.

Set gear selector lever to D position.

4.

Move selector lever to P position.

5.

Start engine.

6.

Move selector lever to D position.

7.

Accelerate vehicle by constantly depressing accelerator pedal
half-way.

8.

Does vehicle start from D

1

 ?

 Read gear position.

Yes or No

Yes

>> GO TO 2.

No

>> Go to 

AT-231, "8. Vehicle Cannot Be Started From D

1

"

 .

Continue ROAD TEST.

ATF operating tempera-
ture

:50 - 80

°

C (122 - 176

°

F)

LCIA0043E

LCIA0045E

SAT495G

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

Bang & Olufsen BeoSound 4 Supplement Manual preview
BeoSound 4
Brand: Bang & Olufsen Pages: 6
Bang & Olufsen BeoSound 5 Encore Manual preview
BeoSound 5 Encore
Brand: Bang & Olufsen Pages: 25
Bang & Olufsen BeoCenter 2 Manual preview
BeoCenter 2
Brand: Bang & Olufsen Pages: 28
Panasonic SC-CH72 Operating Instructions Manual preview
SC-CH72
Brand: Panasonic Pages: 89
Garmin GPSMAP 751 Quick Start Manual preview
GPSMAP 751
Brand: Garmin Pages: 4
Tracer Premium Pro USB Instruction Manual preview
Premium Pro USB
Brand: Tracer Pages: 8
Earthworks Audio SR5314 Quick Start Manual preview
SR5314
Brand: Earthworks Audio Pages: 3
Sennheiser AQS e 604 (German) Betriebsanleitung preview
AQS e 604
Brand: Sennheiser Pages: 6
Sennheiser MKE 202 Manual preview
MKE 202
Brand: Sennheiser Pages: 17
DAPAudio 1U fan unit Manual preview
1U fan unit
Brand: DAPAudio Pages: 12
Majorcom: RM-6000 User Manual preview
RM-6000
Brand: Majorcom: Pages: 5
Tablee T0918 User Manual preview
T0918
Brand: Tablee Pages: 4
Delphi SA10201 - Boom Box Audio System Operation Manual preview
SA10201 - Boom Box Audio System
Brand: Delphi Pages: 12
info-hold MP-3000 M Installation Manual preview
MP-3000 M
Brand: info-hold Pages: 2
ewoo eFizz Travel User Manual preview
eFizz Travel
Brand: ewoo Pages: 85
ALLEN & HEATH dLive CDM32 Getting Started User Manual preview
dLive CDM32
Brand: ALLEN & HEATH Pages: 14
Olympus DIRECTREC DR-2000 (French) Mode D'Emploi preview
DIRECTREC DR-2000
Brand: Olympus Pages: 38
Commodore VY-VZ Installation Instructions Manual preview
VY-VZ
Brand: Commodore Pages: 18

Brands by name

Popular brands

Load more brands