manualshive.com logo in svg

Jatco RE4F04B, Manual

The Jatco RE4F04B is a reliable and durable automatic transmission system commonly used in various vehicles. Ensure proper maintenance of your transmission system by downloading the free user manual from manualshive.com to ensure optimal performance and longevity. Keep your vehicle running smoothly with a comprehensive manual at your disposal.

Share
Download
background image

AT-354

[RE4F04B]

REPAIR FOR COMPONENT PARTS

Revision: November 2006

2006 Altima

b.

Move side gear up and down to measure dial indicator deflec-
tion. Always measure indicator deflection on both side gears.

c.

If not within specification, adjust clearance by changing thick-
ness of differential side gear thrust washers.

4.

Install lock pin using Tool

CAUTION:

Make sure the pin is flush with case.

5.

Install speedometer drive gear on differential case.

CAUTION:

Align the projection of speedometer drive gear with the
groove of differential case.

6.

Press on differential side bearings using Tool.

Clearance between side 
gear and differential 
case with washer

: 0.1 - 0.2 mm 
(0.004 - 0.008 in)

Differential side gear 
thrust washers

: Refer to 

AT-382, "DIF-

FERENTIAL SIDE GEAR 
THRUST WASHERS"

 .

SMT611A

Tool number

:KV32101000 (J-25689-A)

SCIA5395E

SAT313D

Tool number

: ST33230000 (J-25805-01)

SCIA5397E

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

NEC AccuSync 120 Advanced Features Manual preview
AccuSync 120
Brand: NEC Pages: 12
Panasonic SC-PMX9DB Quick Manual preview
SC-PMX9DB
Brand: Panasonic Pages: 1
Panasonic SC-AKX18 Operating Instructions preview
SC-AKX18
Brand: Panasonic Pages: 2
Panasonic SC-PM02 Operating Instructions preview
SC-PM02
Brand: Panasonic Pages: 2
Panasonic SC-PMX90 Owner'S Manual preview
SC-PMX90
Brand: Panasonic Pages: 20
Motorvac TransTech III+ User Manual preview
TransTech III+
Brand: Motorvac Pages: 16
ooma Linx 700-0120-501 Quick Start Manual preview
Linx 700-0120-501
Brand: ooma Pages: 10
Bogen BCBM Instruction Manual preview
BCBM
Brand: Bogen Pages: 12
Senal SCM-600 User Manual preview
SCM-600
Brand: Senal Pages: 12
WOXTER Mic Studio 50 Manual preview
Mic Studio 50
Brand: WOXTER Pages: 36
Korg MS-02 Owner'S Manual preview
MS-02
Brand: Korg Pages: 6
McIntosh MXA70 Owner'S Manual preview
MXA70
Brand: McIntosh Pages: 32
Fame Audio Studio CO2 Manual preview
Studio CO2
Brand: Fame Audio Pages: 10
Curtis RCD739UK Instruction Manual preview
RCD739UK
Brand: Curtis Pages: 9
Sharp XL-1000H Service Manual preview
XL-1000H
Brand: Sharp Pages: 72
Kenwood XD-355 Instruction Manual preview
XD-355
Brand: Kenwood Pages: 40
Kenwood RXD-V333 Service Manual preview
RXD-V333
Brand: Kenwood Pages: 43
Kenwood RXD-V252 Service Manual preview
RXD-V252
Brand: Kenwood Pages: 26

Brands by name

Popular brands

Load more brands