manualshive.com logo in svg

Jatco RE4F04B, Manual

The Jatco RE4F04B is a reliable and durable automatic transmission system commonly used in various vehicles. Ensure proper maintenance of your transmission system by downloading the free user manual from manualshive.com to ensure optimal performance and longevity. Keep your vehicle running smoothly with a comprehensive manual at your disposal.

Share
Download
background image

AT-52

[RE4F04B]

ON BOARD DIAGNOSTIC SYSTEM DESCRIPTION

Revision: November 2006

2006 Altima

PN position (PNP) 
switch

PN POSI SW
[ON/OFF]

X

—

●

ON/OFF state com-
puted from signal of 
PN position SW is 
displayed.

R position switch

R POSITION 
SW
[ON/OFF]

X

—

●

ON/OFF state com-
puted from signal of 
R position SW is dis-
played.

D position switch

D POSITION 
SW
[ON/OFF]

X

—

●

ON/OFF state com-
puted from signal of 
D position SW is dis-
played.

2 position switch

2 POSITION 
SW
[ON/OFF]

X

—

●

ON/OFF status, 
computed from sig-
nal of 2 position SW, 
is displayed.

1 position switch

1 POSITION 
SW
[ON/OFF]

X

—

●

ON/OFF status, 
computed from sig-
nal of 1 position SW, 
is displayed.

ASCD cruise signal

ASCD·CRUIS
E
[ON/OFF]

X

—

●

Status of ASCD 
cruise signal is dis-
played.
ON ... Cruising state
OFF ... Normal run-
ning state

ASCD OD cut signal

ASCD·OD 
CUT
[ON/OFF]

X

—

●

Status of ASCD OD 
release signal is dis-
played.
ON ... OD released
OFF ... OD not 
released

Kickdown switch

KICKDOWN 
SW
[ON/OFF]

X

—

●

ON/OFF status, 
computed from sig-
nal of kickdown SW, 
is displayed.

●

This is displayed even when no 
kickdown switch is equipped.

Stop lamp switch

BRAKE SW
[ON/OFF]

X

—

—

●

ON/OFF status is 
displayed.
ON ... Brake pedal is 
depressed.
OFF ... Brake pedal 
is released.

Selector lever position

SLCT LVR 
POSI

—

X

●

Selector lever posi-
tion data, used for 
computation by 
TCM, is displayed.

●

A specific value used for con-
trol is displayed if fail-safe is 
activated due to error.

Vehicle speed

VEHICLE 
SPEED
[km/h] or 
[mph]

—

X

●

Vehicle speed data, 
used for computa-
tion by TCM, is dis-
played.

Throttle position 
[Accelerator pedal 
position (APP) sensor]

THROTTLE 
POSI
[/8]

—

X

—

●

Throttle position 
data, used for com-
putation by TCM, is 
displayed.

●

A specific value used for con-
trol is displayed if fail-safe is 
activated due to error.

Item

Display

Monitor item

Description

Remarks

TCM 
Input 

signals

Main 

signals

Selec-

tion 

from 

menu

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

Samson Q1 Owner'S Manual preview
Q1
Brand: Samson Pages: 4
Yealink T48S Skype For Business Edition Startup Manual preview
T48S Skype For Business Edition
Brand: Yealink Pages: 3
Samson Q6 Owner'S Manual preview
Q6
Brand: Samson Pages: 4
Sennheiser MD 425 Instructions For Use Manual preview
MD 425
Brand: Sennheiser Pages: 10
Fame Audio Studio CU1 Manual preview
Studio CU1
Brand: Fame Audio Pages: 9
AKG PERCEPTION 420 User Instructions preview
PERCEPTION 420
Brand: AKG Pages: 15
Magnavox MAS-30037 Specifications preview
MAS-30037
Brand: Magnavox Pages: 1
Speco CAMMIC3.5 User Manual preview
CAMMIC3.5
Brand: Speco Pages: 3
Trevi SB 8350TV User Manual preview
SB 8350TV
Brand: Trevi Pages: 24
Work Pro Roader 408 User Manual preview
Roader 408
Brand: Work Pro Pages: 12
Vigitron MaxiiCopper Vi2701TX Installation Manual preview
MaxiiCopper Vi2701TX
Brand: Vigitron Pages: 2
Neat Microphones Beecaster Field Manual preview
Beecaster
Brand: Neat Microphones Pages: 12
RCA RS2010 User Manual preview
RS2010
Brand: RCA Pages: 20
AV Department Confidea G3 Quick Manual preview
Confidea G3
Brand: AV Department Pages: 15
Apex Digital APEX460 - TECHNICAL SHETT Manual preview
APEX460 - TECHNICAL SHETT
Brand: Apex Digital Pages: 3
Samsung MX-D730D User Manual preview
MX-D730D
Brand: Samsung Pages: 40
Samsung MX-FS8000 User Manual preview
MX-FS8000
Brand: Samsung Pages: 42
Toa WT-780 Specifications preview
WT-780
Brand: Toa Pages: 2

Brands by name

Popular brands

Load more brands