manualshive.com logo in svg

Jatco RE4F04B, Manual

The Jatco RE4F04B is a reliable and durable automatic transmission system commonly used in various vehicles. Ensure proper maintenance of your transmission system by downloading the free user manual from manualshive.com to ensure optimal performance and longevity. Keep your vehicle running smoothly with a comprehensive manual at your disposal.

Share
Download
background image

SERVICE DATA AND SPECIFICATIONS (SDS)

AT-385

[RE4F04B]

D

E

F

G

H

I

J

K

L

M

A

B

AT

Revision: November 2006

2006 Altima

Bearing Retainer

ECS009BW

SEAL RING CLEARANCE

Total End Play

ECS009BX

BEARING RACE FOR ADJUSTING TOTAL END PLAY

*: Always check with the Parts Department for the latest parts information.

Reverse Clutch End Play

ECS009BY

THRUST WASHERS FOR ADJUSTING REVERSE CLUTCH DRUM END PLAY

*: Always check with the Parts Department for the latest parts information.

Removal and Installation

ECS009BZ

Unit: mm (in)

Shift Solenoid Valves

ECS009C0

Solenoid Valves

ECS009C1

Bearing retainer seal ring 
clearance

mm (in)

Standard

0.10 - 0.30 (0.0039 - 0.0118)

Allowable limit

0.30 (0.0118)

Total end play

mm (in)

0.25 - 0.55 (0.0098 - 0.0217)

Thickness

mm (in)

Part number*

0.8 (0.031)
1.0 (0.039)
1.2 (0.047)
1.4 (0.055)
1.6 (0.063)
1.8 (0.071)
2.0 (0.079)
0.9 (0.035)
1.1 (0.043)
1.3 (0.051)
1.5 (0.059)
1.7 (0.067)
1.9 (0.075)

31435-80X00
31435-80X01
31435-80X02
31435-80X03
31435-80X04
31435-80X05
31435-80X06
31435-80X09
31435-80X10

31435-80X11

31435-80X12
31435-80X13
31435-80X14

Reverse clutch end play

mm (in)

0.61 - 1.00 (0.0240 - 0.0394)

Thickness

mm (in)

Part number*

0.80 (0.0315)
0.95 (0.0374)
1.10 (0.0433)
1.25 (0.0492)
1.40 (0.0551)
1.55 (0.0610)
1.70 (0.0669)
1.85 (0.0728)

31508-80X13
31508-80X14
31508-80X15
31508-80X16
31508-80X17
31508-80X18
31508-80X19
31508-80X20

Distance between end of converter housing and torque converter

14 (0.55)

Gear position

1

2

3

4

Shift solenoid valve A

ON (Closed)

OFF (Open)

OFF (Open)

ON (Closed)

Shift solenoid valve B

ON (Closed)

ON (Closed)

OFF (Open)

OFF (Open)

Solenoid valves

Resistance (Approx.)

Ω

Terminal No.

Shift solenoid valve A

20 - 30

2

Shift solenoid valve B

5 - 20

1

Overrun clutch solenoid valve

20 - 30

3

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

Sennheiser MKE PLATINUM Product Sheet preview
MKE PLATINUM
Brand: Sennheiser Pages: 1
Cetacea Sound Orbiter Pod Quick Start Manual preview
Orbiter Pod
Brand: Cetacea Sound Pages: 4
Nady Systems AMERICAN STARPOWER X2 Operating Instructions preview
AMERICAN STARPOWER X2
Brand: Nady Systems Pages: 2
miniDSP AMBIMIK-1 User Manual preview
AMBIMIK-1
Brand: miniDSP Pages: 21
Medion LIFE P64014 User Manual preview
LIFE P64014
Brand: Medion Pages: 220
Aiwa CX-NA71 Operating Instructions Manual preview
CX-NA71
Brand: Aiwa Pages: 80
Takstar DA-237 User Manual preview
DA-237
Brand: Takstar Pages: 2
Chord 171.921UK User Manual preview
171.921UK
Brand: Chord Pages: 5
AKG PERCEPTION 420 User Instructions preview
PERCEPTION 420
Brand: AKG Pages: 15
PCB Piezotronics 377B40 Installation And Operating Manual preview
377B40
Brand: PCB Piezotronics Pages: 9
Hama 00040980 Operation User'S Manual preview
00040980
Brand: Hama Pages: 53
NEEWER NW-8000-USB Instruction Manual preview
NW-8000-USB
Brand: NEEWER Pages: 26
Shure SLX2 Service Manual preview
SLX2
Brand: Shure Pages: 35
Apex Digital APEX188 Installation And Operation preview
APEX188
Brand: Apex Digital Pages: 2
DS MINT 220 User Manual preview
MINT 220
Brand: DS Pages: 7
AEG BSS 4804 Instruction Manual preview
BSS 4804
Brand: AEG Pages: 58
AEG BSS 4806 Instruction Manual preview
BSS 4806
Brand: AEG Pages: 66
AEG BSS 4808 Manual preview
BSS 4808
Brand: AEG Pages: 90

Brands by name

Popular brands

Load more brands