Jatco RE4F04B Manual Download Page 463

Page: 463 / 708

TROUBLE DIAGNOSIS

AT-463

[RE5F22A]

Revision: November 2006

2006 Altima

●

For details, refer to the separate “CONSULT-II Operations Man-
ual”.

Turn ignition switch “OFF”.

Connect CONSULT-II and CONSULT-II CONVERTER to data
link connector, which is located in driver instrument panel
(lower).

Turn ignition switch “ON”. (Do not start engine.)

Touch “START (NISSAN BASED VHCL)”.

Touch “A/T”.
If “A/T” is not indicated, go to

GI-39, "Consult-II Data Link Con-

nector (DLC) Circuit"

Perform each diagnostic test mode according to each service
procedure.

WORK SUPPORT MODE
Work item

SELF-DIAG RESULT MODE
Operation procedure

Perform “CONSULT-II SETTING PROCEDURE”. Refer to

AT-462, "CONSULT-II SETTING PROCE-

DURE"

LCIA0042E

BCIA0029E

BCIA0030E

Work item

Condition

Usage

INITIALIZATION

Under the following conditions.

●

Ignition switch “ON”.

●

Selector lever “P” or “N” position.

●

Engine not running.

●

Vehicle speed is 0 km/h (0 MPH).

●

Ignition voltage is more than 10.5V.

●

Malfunction was not detected.

Use to initialize TCM in a case of replacing tran-
saxle or TCM. Refer to

AT-390, "Precautions for

A/T Assembly or TCM Replacement"

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for RE4F04B

Reviews:

Jatco RE4F04B, Manual, Page: 463 / 708

Search results

Summary of Contents for RE4F04B

Reviews: