manualshive.com logo in svg

Jatco RE4F04B, Manual

The Jatco RE4F04B is a reliable and durable automatic transmission system commonly used in various vehicles. Ensure proper maintenance of your transmission system by downloading the free user manual from manualshive.com to ensure optimal performance and longevity. Keep your vehicle running smoothly with a comprehensive manual at your disposal.

Share
Download
background image

AT-674

[RE5F22A]

REPAIR FOR COMPONENT PARTS

Revision: November 2006

2006 Altima

8.

Install B5 brake cushion plate.

CAUTION:

Take care with direction of B5 brake cushion plate.

9.

Install B5 brake flange, B5 brake plates and B5 brake discs as
shown.

10. Install snap ring using suitable tool.

11. Install new O-ring in accumulator cover.

CAUTION:

●

Do not reuse O-ring.

●

Apply ATF to new O-ring.

12. Install new seal ring in forward clutch accumulator piston.

CAUTION:

●

Do not reuse seal ring.

●

Apply ATF to new seal ring.

13. Install forward clutch accumulator piston, compression spring

and accumulator cover in transaxle case cover.

14. Tighten accumulator cover torx bolts to specified torque. Refer

to 

AT-670, "COMPONENTS"

 .

15. Install new seal rings and bearing race in transaxle case cover.

Refer to 

AT-678, "ASSEMBLY"

  to select proper bearing race.

CAUTION:

●

Do not reuse seal rings.

●

Apply ATF to new O-rings.

SCIA4245E

SCIA4244E

SCIA4243E

WCIA0386E

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

Panasonic KX-NS700 Programming Manual preview
KX-NS700
Brand: Panasonic Pages: 58
Panasonic NS700 Manager User Manual preview
NS700
Brand: Panasonic Pages: 7
Raymarine A65 Installation And Operation Instructions Manual preview
A65
Brand: Raymarine Pages: 308
Radiant Communications VA700 Instruction Manual preview
VA700
Brand: Radiant Communications Pages: 11
Concertone RV2003H Operating Instructions Manual preview
RV2003H
Brand: Concertone Pages: 12
Olympus ME31 Instructions preview
ME31
Brand: Olympus Pages: 2
Honeywell V4000 Installation And Setup Manual preview
V4000
Brand: Honeywell Pages: 16
Honeywell Notifier DVC MIC-1 Installation Document preview
Notifier DVC MIC-1
Brand: Honeywell Pages: 6
Honeywell IDENTLOC 032220.17 Mounting And Connection Instructions preview
IDENTLOC 032220.17
Brand: Honeywell Pages: 8
Honeywell RK-MIC Product Instructions preview
RK-MIC
Brand: Honeywell Pages: 14
Honeywell V4000 Installation Manual preview
V4000
Brand: Honeywell Pages: 2
Honeywell Fire-Lite ECC-RM Product Installation Document preview
Fire-Lite ECC-RM
Brand: Honeywell Pages: 2
Valcom V-9970 User Manual preview
V-9970
Brand: Valcom Pages: 6
Panasonic WM-KC20N Brochure & Specs preview
WM-KC20N
Brand: Panasonic Pages: 5
Panasonic KX-HNC855 Quick Start Manual preview
KX-HNC855
Brand: Panasonic Pages: 2
Panasonic : WX-LR100/A Product Introduction preview
: WX-LR100/A
Brand: Panasonic Pages: 20
Panasonic Ramsa WX-RP158 Operating Instructions Manual preview
Ramsa WX-RP158
Brand: Panasonic Pages: 14
Panasonic AJ-MC700P Operating Instructions Manual preview
AJ-MC700P
Brand: Panasonic Pages: 12

Brands by name

Popular brands

Load more brands