manualshive.com logo in svg

Jatco RE4F04B, Manual

The Jatco RE4F04B is a reliable and durable automatic transmission system commonly used in various vehicles. Ensure proper maintenance of your transmission system by downloading the free user manual from manualshive.com to ensure optimal performance and longevity. Keep your vehicle running smoothly with a comprehensive manual at your disposal.

Share
Download
background image

AT-694

[RE5F22A]

ASSEMBLY

Revision: November 2006

2006 Altima

38. Install thrust washer and one- way clutch outer race sub assem-

bly in oil pump assembly.

CAUTION:

Apply petroleum jelly to thrust washer.

39. Check the distance of “B”.

CAUTION:

If the distance is out of standards, adjust within standards
again.

40. Place oil pump assembly through the input shaft in horizontal

position, and align the bolt holes of the oil pump assembly with
transaxle case. Lightly press oil pump assembly.

CAUTION:

Do not drop one-way clutch outer race sub assembly.

41. Tighten oil pump assembly bolts to specified torque. Refer to 

AT-

634, "Components"

 .

SCIA4274E

“B”

: 51.09 - 51.71 mm (2.0114 - 2.0358 in)

SCIA4275E

SCIA4276E

SCIA4156E

SCIA4157E

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

Earthworks P30 Owner'S Manual preview
P30
Brand: Earthworks Pages: 2
FeiYu Tech MIC Quick Start Manual preview
MIC
Brand: FeiYu Tech Pages: 8
Velodyne MIC-5 - DATASHEET 1 Datasheet preview
MIC-5 - DATASHEET 1
Brand: Velodyne Pages: 2
Neumann U 87 AI Stereo Operating Instructions Manual preview
U 87 AI Stereo
Brand: Neumann Pages: 9
AKG CM-311A Quick Manual preview
CM-311A
Brand: AKG Pages: 2
Nady Systems RSM-1 User Manual preview
RSM-1
Brand: Nady Systems Pages: 2
RELACART UR-260D Installation And Operation Manual preview
UR-260D
Brand: RELACART Pages: 11
Laser SPK-F220 Quick User Manual preview
SPK-F220
Brand: Laser Pages: 3
Roland DR-80C Owner'S Manual preview
DR-80C
Brand: Roland Pages: 6
Guardian Audio IQ series Owner'S Manual preview
IQ series
Brand: Guardian Audio Pages: 4
SABINE TRUE MOBILITY WIRELESS SYSTEM SWM3000 Operating Manual preview
TRUE MOBILITY WIRELESS SYSTEM SWM3000
Brand: SABINE Pages: 40
G-Lab K-MIC NATRIUM User Manual preview
K-MIC NATRIUM
Brand: G-Lab Pages: 8
Inovalley Retro 03 Manual preview
Retro 03
Brand: Inovalley Pages: 12
Panasonic SA-AK350E Service Manual preview
SA-AK350E
Brand: Panasonic Pages: 100
Panasonic RX-C52 Operating Instructions Manual preview
RX-C52
Brand: Panasonic Pages: 20
Panasonic VA-1232 Installation And Programming Manual preview
VA-1232
Brand: Panasonic Pages: 152
Omnitronic WM-224 User Manual preview
WM-224
Brand: Omnitronic Pages: 16
Panasonic SA-CH32 Service Manual preview
SA-CH32
Brand: Panasonic Pages: 59

Brands by name

Popular brands

Load more brands