manualshive.com logo in svg

Jatco RE4F04B, Manual

The Jatco RE4F04B is a reliable and durable automatic transmission system commonly used in various vehicles. Ensure proper maintenance of your transmission system by downloading the free user manual from manualshive.com to ensure optimal performance and longevity. Keep your vehicle running smoothly with a comprehensive manual at your disposal.

Share
Download
background image

AT-406

[RE5F22A]

A/T CONTROL SYSTEM

Revision: November 2006

2006 Altima

POWER TRANSMISSION 
“N” position

Since both the forward clutch and the direct clutch are released, torque from the input shaft drive is not trans-
mitted to the output shaft.

“P” position

●

The same as for the “N” position, both the forward clutch and the direct clutch are released, so torque
from the input shaft drive is not transmitted to the output shaft.

●

The parking pole linked with the selector lever meshes with the parking gear and fastens the output shaft
mechanically.

1.

Forward clutch

2.

Direct clutch

3.

U/D clutch

4.

2nd coast brake

5.

2nd brake

6.

1st and reverse brake

7.

U/D brake

8.

B5 brake

9.

One-way clutch No. 1

10. One-way clutch No. 2

11. Main sun gear

12. Main planetary carrier

13. Main front internal gear

14. Main rear internal gear

15. U/D sun gear

16. U/D front planetary carrier

17. U/D front internal gear

18. U/D rear planetary carrier

19. U/D rear internal gear

20. Input shaft

21. Counter drive gear

22. Counter driven gear

23. Output shaft

24. Parking gear

25. Parking pawl

SCIA2577E

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

NEC SV8300 Manual preview
SV8300
Brand: NEC Pages: 54
NEC ELECTRA ELITE IPK II General Description Manual preview
ELECTRA ELITE IPK II
Brand: NEC Pages: 174
NEC Xen Master System Hardware Manual preview
Xen Master
Brand: NEC Pages: 268
NEC NEAX 2000 User Manual preview
NEAX 2000
Brand: NEC Pages: 10
B&G electronics DUAL-VOX LTE-02 Installation And Operation Manual preview
DUAL-VOX LTE-02
Brand: B&G electronics Pages: 3
S.E.M. Fusion Z-7799 Quick Start Manual preview
Fusion Z-7799
Brand: S.E.M. Pages: 6
Tokai LRD-3050W Instruction Manual preview
LRD-3050W
Brand: Tokai Pages: 20
Austrian Audio OD505 Quick Start Manual preview
OD505
Brand: Austrian Audio Pages: 2
Sandstrom SHFUSB10 Instruction Manual preview
SHFUSB10
Brand: Sandstrom Pages: 32
Teac GF-650 Service Manual preview
GF-650
Brand: Teac Pages: 23
4EVAC 4E-FMWB Installation And User Manual preview
4E-FMWB
Brand: 4EVAC Pages: 17
Sennheiser E 825 S - 07-06 Instructions For Use Manual preview
E 825 S - 07-06
Brand: Sennheiser Pages: 9
Focal SCALA UTOPIA III EVO User Manual preview
SCALA UTOPIA III EVO
Brand: Focal Pages: 52
Rockville RWM-4US Owner'S Manual preview
RWM-4US
Brand: Rockville Pages: 10
UMT MICPRO UHF-5100 User Manual preview
MICPRO UHF-5100
Brand: UMT Pages: 4
Nady Systems RSM-4 User Manual preview
RSM-4
Brand: Nady Systems Pages: 2
Apex Digital APEX205 Instructions preview
APEX205
Brand: Apex Digital Pages: 2
Hengbida Electronic Technology Sound Pad S1 Product Manual preview
Sound Pad S1
Brand: Hengbida Electronic Technology Pages: 19

Brands by name

Popular brands

Load more brands