manualshive.com logo in svg

Jatco RE4F04B, Manual

The Jatco RE4F04B is a reliable and durable automatic transmission system commonly used in various vehicles. Ensure proper maintenance of your transmission system by downloading the free user manual from manualshive.com to ensure optimal performance and longevity. Keep your vehicle running smoothly with a comprehensive manual at your disposal.

Share
Download
background image

AT-274

[RE4F04B]

AIR BREATHER HOSE

Revision: November 2006

2006 Altima

2.

Disconnect the air breather hose air cleaner to electronic throttle control actuator tube side and transaxle
side of the oil catch tank.

3.

Remove the oil catch tank.

Installation

Installation is in the reverse order of removal.

CAUTION:

Do not crush or kink the air breather hose during installation.

NOTE:

●

The paint marks must face upwards on installation.

●

Insert air breather hose (transaxle side) B into tube stopper
when installing air breather hose to the oil catch tank.

●

Insert air breather hose (transaxle side) A into the point where
the radius stops on the air breather hose when installing to the
transaxle.

WCIA0369E

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

Magnavox FW391C Manual preview
FW391C
Brand: Magnavox Pages: 26
Sanken CU-55 Instruction Manual preview
CU-55
Brand: Sanken Pages: 2
Samson CM11B Specifications preview
CM11B
Brand: Samson Pages: 2
Omnitronic VRM-2200 PRO USB User Manual preview
VRM-2200 PRO USB
Brand: Omnitronic Pages: 2
HQ Power MICW81 User Manual preview
MICW81
Brand: HQ Power Pages: 29
Entel EA19 Quick Start User Manual preview
EA19
Brand: Entel Pages: 4
Shure UA UC User Manual Supplement preview
UA UC
Brand: Shure Pages: 8
LENCO PMX-160BK User Manual preview
PMX-160BK
Brand: LENCO Pages: 66
IC Audio M-E 01 Manual preview
M-E 01
Brand: IC Audio Pages: 2
Exibel BDX600 User Manual preview
BDX600
Brand: Exibel Pages: 84
Telefunken TF-MSM2.102 Instruction Manual preview
TF-MSM2.102
Brand: Telefunken Pages: 18
Better Music Builder tour+ Musicmusic pad TM-81 Owner'S Manual preview
tour+ Musicmusic pad TM-81
Brand: Better Music Builder Pages: 16
Recatech RR950 RETRO JUKEBOX User Manual preview
RR950 RETRO JUKEBOX
Brand: Recatech Pages: 25
Ecler MPAGE1 User Manual preview
MPAGE1
Brand: Ecler Pages: 24
Ecler Dante PAGENETDN User Manual preview
Dante PAGENETDN
Brand: Ecler Pages: 25
Telex 785H Specifications preview
785H
Brand: Telex Pages: 2
K&K Sound Systems Meridian PRO Installation Instructions preview
Meridian PRO
Brand: K&K Sound Systems Pages: 5
Aiwa NSX-D77 Operating Instructions Manual preview
NSX-D77
Brand: Aiwa Pages: 27

Brands by name

Popular brands

Load more brands