manualshive.com logo in svg

Jatco RE4F04B, Manual

The Jatco RE4F04B is a reliable and durable automatic transmission system commonly used in various vehicles. Ensure proper maintenance of your transmission system by downloading the free user manual from manualshive.com to ensure optimal performance and longevity. Keep your vehicle running smoothly with a comprehensive manual at your disposal.

Share
Download
background image

AT-210

[RE4F04B]

DTC CONTROL UNIT (RAM), CONTROL UNIT (ROM)

Revision: November 2006

2006 Altima

Diagnostic Procedure

ECS0099Q

1. 

INSPECTION START

 With CONSULT-II

1.

Turn ignition switch ON and select “SELF DIAGNOSIS” mode for A/T with CONSULT-II.

2.

Touch “ERASE”.

3.

Perform 

AT-209, "Diagnostic Trouble Code (DTC) Confirmation Procedure"

 .

4.

Is the “CONTROL UNIT (RAM)” or “CONTROL UNIT (ROM)” displayed again?

Yes or No

Yes

>> Replace TCM.

No

>> INSPECTION END

Summary of Contents for RE4F04B





































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for RE4F04B

NEC SV8300 Manual preview
SV8300
Brand: NEC Pages: 54
NEC ELECTRA ELITE IPK II General Description Manual preview
ELECTRA ELITE IPK II
Brand: NEC Pages: 174
NEC Xen Master System Hardware Manual preview
Xen Master
Brand: NEC Pages: 268
VocoPro DA-2277 User Manual preview
DA-2277
Brand: VocoPro Pages: 26
Takstar E-340 Quick Start Manual preview
E-340
Brand: Takstar Pages: 2
SereneLife SLBSP10 Quick Manual preview
SLBSP10
Brand: SereneLife Pages: 2
Shure Unidyne A 581SA Datasheet preview
Unidyne A 581SA
Brand: Shure Pages: 4
Akai AMP300UCI Operator'S Manual preview
AMP300UCI
Brand: Akai Pages: 38
Magnavox FW 340C (Spanish) Manual De Usuario preview
FW 340C
Brand: Magnavox Pages: 25
Extron electronics VoiceLift Pro VLS 3001 User Manual preview
VoiceLift Pro VLS 3001
Brand: Extron electronics Pages: 41
Bacharach CO2 Monitor 2800 Instruction preview
CO2 Monitor 2800
Brand: Bacharach Pages: 16
Signal inconcert pro User Manual preview
inconcert pro
Brand: Signal Pages: 16
Exibel KW-1011B Instruction Manual preview
KW-1011B
Brand: Exibel Pages: 32
Sharp QT-CD210H Serivce Manual preview
QT-CD210H
Brand: Sharp Pages: 36
Panasonic Easa-Phone KX-T2365 Operating Instructions Manual preview
Easa-Phone KX-T2365
Brand: Panasonic Pages: 7
Panasonic Digital Super Hybrid System Reference Manual preview
Digital Super Hybrid System
Brand: Panasonic Pages: 12
Sharp CD-MPS600 Service Manual preview
CD-MPS600
Brand: Sharp Pages: 100
Phonak DynaMic User Manual preview
DynaMic
Brand: Phonak Pages: 20

Brands by name

Popular brands

Load more brands