manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 92 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 92

92 

Installation and Service Guide: Color Controller E-36A

Performing Backup and Restore

To backup manually

1

In 

Fiery System Restore

, select one of the following options:

•

Backup Now

> 

USB

: Select this option if you want to create a backup on a USB storage device.

•

New image

:

 Select this option if you want to create a new backup of the current E-36A. You can select 

Create 

bootable image

 option to make the USB storage device a bootable device. 

•

Fiery factory image

:

 Select this option if you want to create a backup of the E-36A factory image. When you 

select this option, the 

Create bootable image

 option enables automatically. 

If you select 

Create bootable image 

option, the USB storage device specified as a destination becomes a bootable 

device. Select this option when you want to boot the E-36A from the backup device to avoid the situation where 

the HDD fails and cannot boot the E-36A. See 

page

 93

 for booting from the bootable device. Bootable device is 

used for system restoration when a hardware failure occurs.

Note:

 

The minimum size required for the USB storage device depends on the actual size of the backup file. You 

can determine the size of the backup file by checking the 

Estimated size

: field in the 

Create USB Backup

 dialog 

box. Prepare a USB storage device with enough capacity. 

Note:

 

Due to Windows file system restriction, the maximum size of the USB flash drive you can use is 32GB, if 

you enable the 

Create bootable image

 option. You can use the USB flash drive with more than 32GB capacity 

without enabling the 

Create bootable image 

option. 

•

Backup Now

> 

Internal hard drive

: Select this option if you want to create a backup on the E-36A HDD. You 

must specify the file name of the backup image. The default image name is the server name of the E-36A.

2

If you selected USB, make sure to attach the USB storage device to one of the USB 3.0 ports on the E-36A.

Note:

 

If the capacity of the USB storage device is less than size of the value listed in 

Estimated size

: field, the backup 

process will not take place. 

3

Click 

Continue

. 

To restore the backup image

1

Access Fiery System Restore (see 

page

 90

).

2

In 

Fiery System Restore

, click 

Restore

.

If you have not logged in as an 

Administrator

 user, you are required to do so. Enter the administrator’s password 

and click 

Log In

.

3

Make sure the E-36A backup image is accessible from the E-36A.

If you want to restore the E-36A backup image stored on a USB storage device, attach the USB storage device to 

one of the USB 3.0 ports on the E-36A.

Summary of Contents for E-36A


































































































































Reviews:

No comments