manualshive.com logo in svg

EFI E-36A, Installation And Service Manual, Page: 20 / 129

Share
Download
EFI E-36A Installation And Service Manual Download Page 20

20 

Installation and Service Guide: Color Controller E-36A

Installing Hardware

4

Remove the top container and any packing material.

5

Carefully lift the E-36A out of the box (see 

“Lift the E-36A carefully”

 on page

 16).

If you notice shipping damage to any component, save the shipping container, in case the carrier needs to see it. 

Call the carrier immediately to report the damage and file a claim.

Connecting the E-36A

You are now ready to make the following connections:

•

Monitor, keyboard and mouse (optional) (see 

page

 21

)

Note:

 

Monitor, keyboard, and mouse are included with the optional Fiery NX One Station kit.

•

Power cable (see 

page

 22

)

•

Printer interface (Crossover Ethernet) cable (see 

page

 22

)

•

Network cable (see 

page

 24

)

•

USB power cable for power synchronization with printer (see 

page

 25

)

Summary of Contents for E-36A


































































































































Reviews:

No comments